Ford 2010 Flex v.1 Manuale Utente

Introduction 5Instrument Cluster 12Warning lights and chimes 12Gauges 16Message center 18Entertainment Systems 28AM/FM stereo with CD/MP3 28Auxiliary

These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag

The power outlet is not designed for the following electric appliances;they may not work properly:• Cathode ray tube type televisions.• Motor loads, s

POWER WINDOWSWARNING: Do not leave children unattended in the vehicle anddo not let children play with the power windows. They mayseriously injure the

To operate one-touch up:• Pull the switch completely up tothe second detent and releasequickly. The window will closefully. Momentarily press theswitc

INTERIOR MIRRORThe interior rear view mirror has two pivot points on the support armwhich lets you adjust the mirror up or down and from side to side.

Heated outside mirrors (if equipped)Both mirrors are heatedautomatically to remove ice, mistand fog when the rear windowdefrost is activated.Do not re

WARNING: Do not use the speed control in heavy traffic or onroads that are winding, slippery or unpaved.Using speed controlThe speed controls are loca

Increasing speed while using speed controlTo set a higher speed:• Press and hold SET + until you get to the desired speed, then release.You can also u

MEDIA: Press repeatedly to select:• AM, FM1, FM2, or CD• DVD/FES (if equipped)• SAT1, SAT2 or SAT3 (Satellite radio mode if equipped).• LINE IN (Auxil

Navigation system/SYNC威 handsfree control features (ifequipped)Presscontrol briefly until thevoiceicon appears on theNavigation display to use the voi

Bounce-back: When an obstacle has been detected in the roof openingas the roof is closing, the roof will automatically open and stop at aprescribed po

Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleasePanic Alarm Engine Oi

HomeLink姞 Wireless Control System (if equipped)The HomeLink威 Wireless ControlSystem, located on the driver’s visor,provides a convenient way toreplace

1. Position the end of yourhand-held transmitter 1–3 inches(2–8 cm) away from the HomeLink威button you wish to program (locatedon your visor) while kee

Gate Operator & Canadian ProgrammingDuring programming, yourhand-held transmitter mayautomatically stop transmitting —not allowing enough time for

Erasing HomeLink姞 buttonsTo erase the three programmedbuttons (individual buttons cannotbe erased):• Press and hold the two outerHomeLink威 buttons unt

WARNING: Make sure that people and objects are clear of thegarage door or security device you are programming. Do notprogram the Car2U威 system with th

If you do not know if your garagedoor opener is a rolling code orfixed code device, open your garagedoor opener’s remote control batterycover. If a pa

2. Go to the garage to locate thegarage door opener motor and its“learn” button. You may need aladder to reach the unit and youmay need to remove the

Note: The Car2U威 system allows for three devices to be programmed. Ifyou need to change or replace any of the three devices after it has beeninitially

3. To input these positions into theCar2U威 system, simultaneouslypress all three Car2U威 systembuttons for a few seconds and thenrelease to put the dev

To erase programming on the Car2U威 system (individual buttons cannotbe erased), use the following procedure:1. Firmly press the two outsideCar2U威 syst

WARNING LIGHTS AND CHIMESWarning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause extensive repairs. A wa

To open the liftgate, press thecontrol button located in the top ofthe liftgate pull cup handle tounlatch the liftgate, then pull on theoutside handle

The liftgate will only operate with the vehicle in P (Park).When the liftgate is being power closed, a chime will sound three timesas the liftgate beg

To power open or close theliftgate from the instrumentpanel:Press the button, located on theinstrument panel, once to poweropen or close the liftgate.

To power close the liftgate withthe rear cargo area controlbutton:Press and release the control on theleft rear quarter panel to close theliftgate.Not

• the liftgate is manually closed and left ajar (unlatched)To reset the power liftgate:1. Disconnect the battery for 20 seconds then, reconnect the ba

ROOF RACK SYSTEM (IF EQUIPPED)Loads should never be placed directly on the roof panel. For properfunction of the roof rack system, loads must be place

KEYSYour vehicle is equipped with twoIntegrated Keyhead Transmitters(IKTs). The IKT functions as both aprogrammed ignition key thatoperates all the lo

POWER DOOR LOCKS• Press thecontrol to unlock alldoors.• Press thecontrol to lock alldoors.Smart locksThis feature helps to prevent you from locking yo

Deactivating/activating autolock featureYour vehicle comes with the autolock features activated; there are fourmethods to enable/disable this feature:

Keyless entry keypad autolock enable/disable procedure1. Turn the ignition to the offposition.2. Close all the doors.3. Enter factory–set 5–digit entr

WARNING: Under engine misfire conditions, excessive exhausttemperatures could damage the catalytic converter, the fuelsystem, interior floor coverings

Note: The autounlock feature can be activated/deactivatedindependently of the autolock feature.Power door lock switch autounlock enable/disable proced

Keyless entry keypad autounlock enable/disable procedure1. Turn the ignition to the offposition.2. Close all the doors.3. Enter factory–set 5–digit en

REMOTE ENTRY SYSTEMThe Integrated Keyhead Transmitter (IKT) complies with part 15 of theFCC rules and with RSS-210 of Industry Canada. Operation is su

• Vehicles not equipped with apower liftgateThe typical operating range for your IKT is approximately 33 feet(10 meters). A decrease in operating rang

2. Press and release again within three seconds to unlock all thedoors.The remote entry system activates the illuminated entry feature; thisfeature tu

Car finderPresstwice within three seconds. The horn will chirp and the turnlamps will flash. It is recommended that this method be used to locateyour

Deactivating the memory featureTo deactivate this feature:1. Press and hold either the 1 or 2 control on the driver’s door for fiveseconds. (A tone wi

IKTs, you can either reprogram them yourself, or take all IKTs to yourauthorized dealer for reprogramming.How to reprogram your Integrated Keyhead Tra

• The battery saver will shut off the headlamps 10 minutes after theignition has been turned to the off position.SECURICODE™ KEYLESS ENTRY SYSTEMThe k

5. The doors will lock then unlock to confirm that your personal entrycode has been programmed to the module.Tips:• Do not set a code that uses five o

Airbag readiness: If this light failsto illuminate when the ignition isturned to on, continues to flash orremains on, have the systemserviced immediat

SECURILOCK姞 PASSIVE ANTI-THEFT SYSTEMSecuriLock威 passive anti-theft system is an engine immobilizationsystem. This system is designed to help prevent

Anti-theft indicatorThe anti-theft indicator is located in the instrument panel cluster.• When the ignition is in the offposition, the indicator will

keyless entry transmitter. A maximum of eight coded keys can beprogrammed to your vehicle; only four of these eight keys can be IKTswith remote entry

4. After three seconds but within 10 seconds of turning the ignition tothe 1 (off) position, insert the second previously coded key into theignition.5

MyKey™ Restricted FeaturesStandard settings – These settings cannot be changed• The audio system will be muted whenever Belt-Minder威 is activateduntil

Note: The MyKey™ can be cleared within the same key cycle that it wascreated, otherwise a standard key (Administrator key) is required todisable the M

Check MyKey™ System StatusThe vehicle System Check will provide the status of the followingMyKey™ parameters:• MYKEY MILES — This odometer only tracks

Note: For all vehicles with remote start installed, it is possible toprogram all ’real’ keys as MyKeys™, in which case, you will need to useyour remot

Condition Potential CausesCannot disable MyKey™ • Key in the ignition is a MyKey™• No MyKeys™ are programmed tothe vehicle. Refer to Create aMyKey™ se

PERIMETER ALARM SYSTEM (IF EQUIPPED)The perimeter anti-theft system will help protect your vehicle fromunauthorized entry.If there is any potential pe

Low tire pressure warning:Illuminates when your tire pressureis low. If the light remains on atstart up or while driving, the tirepressure should be c

• Press and hold the 7 • 8 and 9 •0 controls on the keyless entrypad at the same time to lock thedoors (driver’s door must beclosed).There is a 20 sec

SEATINGWARNING: Reclining the seatback can cause an occupant toslide under the seat’s safety belt, resulting in severe personalinjuries in the event o

To adjust the head restraint, do the following:1. Adjust the seatback to an upright driving/riding position. Refer toAdjusting the front manual seat l

To remove the adjustable head restraint, do the following:1. Pull up the head restraint until itreaches the highest adjustmentposition.2. Simultaneous

WARNING: To minimize the risk of neck injury in the event of acrash, head restraints must be installed properly.Adjusting the front manual seat (if eq

Using the manual lumbar support (if equipped)The lumbar control is located on theside of the seat cushion.Turn to adjust lumbar support.Rotate the lum

Adjusting the front power seat (if equipped)WARNING: Never adjust the driver’s seat or seatback when thevehicle is moving.WARNING: Do not pile cargo h

Move the front of the control up ordown to tilt the seat cushion.Move the rear of the control up ordown to raise or lower the seatcushion.Move the con

Using the power lumbar support (if equipped)The power lumbar control is located on the outboard side of the seat.Press the forward side of the control

Memory seat/power mirrors/adjustable pedals (if equipped)This system allows automaticpositioning of the driver seat,outside rearview mirrors andadjust

Headlamps on warning chime: Sounds when the headlamps or parkinglamps are on, the ignition is off (the key is not in the ignition) and thedriver’s doo

REAR SEATSHead restraintsLift the head restraint so that it is located directly or as close as possiblebehind your head.The head restraints can be mov

To remove the adjustable head restraint, do the following:1. Pull up the head restraint until itreaches the highest adjustmentposition.2. Press and ho

Adjusting second row bucket and bench seat backLift the handle to adjust seatback.Using same control will fold theseatback flat.Note: For the bench se

1. Lift the handle located on theside of the seat.The seatback will fold flat.2. Lift the handle all the way upuntil the seat releases from thefloor.

3. To return the seatback to thefloor from tumbled position, rotatethe seat down until you hear itlatching to the floor.4. To return the seatback to t

Press the control located at theback of the rear door opening onetime to fold the seat back down andtumble the seat forward for accessto the 3rd row.E

4. To return the seatback to theupright position• Lift the seatback toward the rearof the vehicle, and• Rotate the seatback until youhear a click, loc

WARNING: Do not adjust or release the seat floor latch whilevehicle is in motion. Do not operate the vehicle with seats intumbled position. Always lat

Stowing the third row seat1. Remove all objects from the seatand stowage tub.2. Stow the head restraints bypressing the head restraint releasebutton w

Note: Do not use the third rowseatback as a load floor when theseatback is folded.Note: In order to allow the seat to latch in the stowed position, do

Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtemperature, the needle will be inthe normal range (between “

2. To return the seatback to uprightposition, pull the number 1 strap,then while holding the number 1strap, pull the long strap located onthe seatback

3. From the rear of the vehicle,tumble the seat by pulling thenumber 2 strap while pulling on thestrap located on the top of theseatback.WARNING: Do n

• Front crash severity sensor.• Restraints Control Module (RCM) with impact and safing sensors.• Restraint system warning light and back-up tone.• The

Driver’s seat position sensorThe driver’s seat position sensor allows your Personal Safety System™ totailor the deployment level of the driver dual-st

Front safety belt pretensionersThe safety belt pretensioners at the front outboard seating positions aredesigned to tighten the safety belts firmly ag

Safety belt precautionsWARNING: Always drive and ride with your seatback uprightand the lap belt snug and low across the hips.WARNING: To reduce the r

WARNING: Front and rear seat occupants, including pregnantwomen, should wear safety belts for optimum protection in anaccident.Combination lap and sho

WARNING: Failure to inspect and replace if necessary the beltand retractor assembly after an accident could increase the riskof injury in a collision.

How to use the automatic locking mode• Buckle the combination lap andshoulder belt.• Grasp the shoulder portion andpull downward until the entirebelt

Front safety belt height adjustmentYour vehicle has safety belt heightadjustments at the front outboardseating positions. Adjust the heightof the shou

MESSAGE CENTERYour vehicle’s message center allows you to configure/personalize certainvehicle options to suit your needs.The message center is also c

WARNING: Do not use extensions to change the fit of theshoulder belt across the torso.Safety belt warning light and indicator chimeThe safety belt war

.Both the driver’s and passenger’s safety belt usages are monitored andeither may activate the Belt-Minder威 feature. The warnings are the samefor the

The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data):Reasons given... Consider...“Crashes are ra

WARNING: Do not sit on top of a buckled safety belt or insert alatchplate into the buckle to avoid the Belt-Minder威 chime. Todo so may adversely affec

3. Wait 10 seconds after the safety belt warning light turns off.• Step 4 must be completed within 20 seconds after the completion ofStep 3.4. For the

Important SRS precautionsThe SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body in

To properly position yourself away from the airbag:• Move your seat to the rear as far as you can while still reaching thepedals comfortably.• Recline

How does the airbag supplemental restraint system work?The airbag SRS is designed toactivate when the vehicle sustainslongitudinal deceleration suffic

WARNING: If the air bag has deployed, the air bag will notfunction again and must be replaced immediately. If the airbag is not replaced, the unrepair

• the system determines that an infant is present in a rear-facing infantseat that is installed according to the manufacturer’s instructions,• the sys

If you calculate your average fuel economy by dividing distance traveledby gallons of fuel used (liters of fuel used by 100 kilometers traveled),your

If a person of adult size is sitting in the front passenger’s seat, but the⬙passenger airbag off⬙ or ⬙pass airbag off⬙ indicator lamp is lit, it ispos

The front passenger sensing system may detect small or medium objectsplaced on the seat cushion. For most objects that are in the frontpassenger seat,

WARNING: To reduce the risk of possible serious injury:Do not stow objects in seat back map pocket (if equipped) orhang objects off seat back if a chi

WARNING: Any alteration/modification to the front passengerseat may affect the performance of the front passenger sensingsystem.Determining if the sys

WARNING: Do not attempt to service, repair, or modify theairbag SRS, its fuses or the seat cover on a seat containing anairbag. Contact your authorize

The fact that the airbags did not inflate in a collision does not mean thatsomething is wrong with the system. Rather, it means the forces werenot of

WARNING: Do not attempt to service, repair, or modify theSafety Canopy威 system, its fuses, the A, B, C or D pillar trim, orthe headliner on a vehicle

• Two crash sensors mounted in the front doors (one on each side ofthe vehicle).• Two crash sensors located at the C pillar behind the rear doors (one

WARNING: If the Safety Canopy威 system has deployed, theSafety Canopy威 will not function again unless replaced. TheSafety Canopy威 system (including the

Disposal of airbags and airbag equipped vehicles(including pretensioners)Contact your authorized dealer as soon as possible. Airbags MUST BEdisposed o

Locks and Security 126Keys 126Locks 127Anti-theft system 140Seating and Safety Restraints 151Seating 151Safety restraints 171Airbags 184Child restrain

System check and vehicle feature customizationPress SETUP repeatedly to cyclethe message center through thefollowing features:RESET FOR SYSTEM CHECKWh

Recommendations for Safety Restraints for ChildrenChild size, height, weight, or ageRecommendedrestraint typeInfantsortoddlersChildren weighing 40 lb

Recommendations for attaching child safety restraints for childrenRestraintTypeChildWeightUse any attachment method as indicatedbelow by “X”LATCH(lowe

WARNING: Never let a passenger hold a child on his or her lapwhile the vehicle is moving. The passenger cannot protect thechild from injury in a colli

Follow all the safety restraint and airbag precautions that apply to adultpassengers in your vehicle.If the child is the proper height, age, and weigh

Installing child safety seats with combination lap and shoulderbeltsCheck to make sure the child seat is properly secured before each use.Children 12

1. Position the child safety seat in aseat with a combination lap andshoulder belt.2. Pull down on the shoulder beltand then grasp the shoulder beltan

4. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) for that seating position untilyou hear

9. Attach the tether strap (if the child seat is equipped). Refer toAttaching child safety seats with tether straps later in this chapter.10. Before p

Your vehicle has LATCH lower anchors for child seat installation at theseating positions marked with the child seat symbol.The LATCH anchors are locat

WARNING: Depending on where you secure a child restraint,and depending on the child restraint design, you may blockaccess to certain safety belt buckl

3. Once “OIL LIFE SET TO XXX%” is displayed, release and pressRESET to change the Oil Life Start Value. Each release and press willreduce the value by

Combining safety belt and LATCH lower anchors for attachingchild safety seatsWhen used in combination, either the safety belt or the LATCH loweranchor

Once the child safety seat has been installed, using either the safety belt,the lower anchors of the LATCH system, or both, you can attach the topteth

• 2nd row bench (60/40)• 3rd rowNote: The cargo tie-downs at therear edge of the floor are nottether anchors.3. Clip the tether strap to theanchor as

Child booster seatsThe belt-positioning booster (booster seat) is used to improve the fit ofthe vehicle safety belt. Children outgrow a typical child

Booster seats should be used until you can answer YES to ALL of thesequestions when seated without a booster seat:• Can the child sit all the way back

• High back booster seatsIf, with a backless booster seat,you cannot find a seating positionthat adequately supports yourchild’s head, a high back boo

If the booster seat slides on the vehicle seat, placing a rubberized meshsold as shelf or carpet liner under the booster seat may improve thisconditio

Child restraint and safety belt maintenanceInspect the vehicle safety belts and child safety seat systems periodicallyto make sure they work properly

NOTICE TO CROSSOVER VEHICLE OWNERSCrossover vehicles handle differentlythan passenger cars in the variousdriving conditions that areencountered on str

Note: Your AWD vehicle is not intended for off-road use. The AWDfeature gives your vehicle some limited off-road capabilities in whichdriving surfaces

TRAILER SWAY CONTROL (if equipped)This feature uses the electronic stability control to mitigate trailer sway,Press RESET to turn it off or on.CREATE

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADINGTire Quality Grades apply to newpneumatic passenger car tires. TheQuality grades can be found whereappli

WARNING: The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not includeacceleration, cornering, hydro

Increasing the inflation pressure beyond this pressure will not increasethe tire’s load carrying capability.• kPa: Kilopascal, a metric unit of air pr

WARNING: Under-inflation is the most common cause of tirefailures and may result in severe tire cracking, tread separationor ⬙blowout⬙, with unexpecte

Note: If you have to drive a distance to get air for your tire(s), checkand record the tire pressure first and add the appropriate air pressurewhen yo

Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them

U.S. DOT Tire Identification Number (TIN)Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the s

WARNING: When mounting replacement tires and wheels, youshould not exceed the maximum pressure indicated on thesidewall of the tire to set the beads w

Safety practicesDriving habits have a great deal to do with your tire mileage and safety.• Observe posted speed limits• Avoid fast starts, stops and t

Wheel misalignment in the front or the rear can cause uneven and rapidtreadwear of your tires and should be corrected by an authorized dealer.Front wh

REAR RIGHT DOOR AJAR — Displayed when the rear right door isnot completely closed.PARK BRAKE ENGAGED — Displayed when the parking brake is set,the eng

• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/All Wheel Drive (AWD)vehicles (front tires at top ofdiagram)Sometimes irregular tire wear can b

Information on “P” type tiresP215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (

Note: You may not find this information on all tires because it is notrequired by federal law.Letter rating Speed rating - mph (km/h)M 81 mph (130 km/

12. Treadwear, Traction and Temperature Grades• Treadwear: The treadwear grade is a comparative rating based on thewear rate of the tire when tested u

Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;

Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8

TIRE PRESSURE MONITORING SYSTEM (TPMS)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe inflation pre

The Tire Pressure Monitoring System complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing tw

Understanding your Tire Pressure Monitoring System (TPMS)The Tire Pressure Monitoring System measures pressure in your fourroad tires and sends the ti

When you believe your system is not operating properlyThe main function of the Tire Pressure Monitoring System is to warn youwhen your tires need air.

TIRE PRESSURE SENSOR FAULT — Displayed when a tire pressuresensor is malfunctioning, or your spare tire is in use. For moreinformation on how the syst

Low Tire PressureWarning LightPossible cause Customer Action RequiredFlashing WarningLightSpare tire in use Your temporary spare tire is inuse. Repair

SNOW TIRES AND CABLES/CHAINSWARNING: Snow tires must be the same size, load index, speedrating as those originally provided by Ford. Use of any tire o

• If possible, avoid fully loading your vehicle.• Remove the tire cables when they are no longer needed. Do not usetire cables on dry roads.• The susp

Payload – is the combined weight of cargo and passengers that thevehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Lab

Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load

GAW (Gross Axle Weight) – is the total weight placed on each axle(front and rear) – including vehicle curb weight and all payload.GAWR (Gross Axle Wei

• Example only:WARNING: Exceeding the Safety Compliance Certification Labelvehicle weight rating limits could result in substandard vehiclehandling or

GCW (Gross Combined Weight) – is the weight of the loaded vehicle(GVW) plus the weight of the fully loaded trailer.GCWR (Gross Combined Weight Rating)

Steps for determining the correct load limit:1. Locate the statement “The combined weight of occupants and cargoshould never exceed XXX kg or XXX lbs.

calculation would be: 635 kg - (2 x 99 kg) - (12 x 45 kg) = 635 - 198 -540 = -103 kg. You will need to reduce the load weight by at least240 lb. (104

CANCELLED BY ADV TRAC EVENT (if equipped) — Displayedwhen the active park feature has been canceled due to theAdvanceTrac威 system activating. Refer to

FWDGCWR (Gross Combined Weight Rating)/Trailer WeightClass MaximumGCWRTrailer weight Tongue loadClass I towing(standard)6900 lb(3131 kg)2000 lb(907 kg

WARNING: Do not exceed the GVWR or the GAWR specified onthe certification label.WARNING: Towing trailers beyond the maximum recommendedgross trailer w

If you use a rental trailer, follow the instructions that the rental agencygives to you.Do not attach safety chains to the bumper.Trailer brakesElectr

Trailer towing tips• Practice turning, stopping and backing up before starting on a trip toget the feel of the vehicle trailer combination. When turni

All Wheel Drive (AWD) vehicles:Tow your All Wheel Drive vehicle with all four wheels on the ground orwith all four wheels off the ground using a vehic

STARTINGPositions of the ignition1. Off— locks the automatictransmission gearshift lever andallows key removal. This positionalso shuts the engine and

WARNING: Do not start your vehicle in a closed garage or inother enclosed areas. Exhaust fumes can be toxic. Always openthe garage door before you sta

• Make sure the gearshift lever is inP (Park).3. Turn the key to 3 (on) withoutturning the key to 4 (start).Some warning lights will briefly illuminat

that assists in starting the engine. After releasing the key from the 4(start) position, the engine may continue cranking for up to 10 secondsor until

WARNING: To reduce the risk of electrical shock, do not useyour heater with ungrounded electrical systems or two-pronged(cheater) adapters.Prior to us

MY KEY ACTIVE DRIVE SAFELY — Displayed at startup whenMyKey™ is in use. Refer to MyKey™ in the Locks and Security chapterfor more information.KEY COUL

How to use the engine block heaterEnsure the receptacle terminals are clean and dry prior to use. To cleanthem, use a dry cloth.Depending on the type

ABS warning lampThe ABS lamp in the instrumentcluster momentarily illuminateswhen the ignition is turned on. Ifthe light does not illuminate duringsta

Press the parking brake pedaldownward again to release theparking brake. Driving with theparking brake on will cause thebrakes to wear out quickly and

WARNING: If a failure has been detected within theAdvanceTrac威 with RSC威 system, the “sliding car” iconwillilluminate steadily and you may hear a chim

When an event occurs that activates AdvanceTrac威 with RSC威 you mayexperience the following:• A slight deceleration of the vehicle• The “sliding car”in

During Electronic Stability Control events the “sliding car” icon in theinstrument cluster will flash.Certain adverse driving maneuvers may activate t

If you switch off the TractionControl, the “sliding car” iconwill illuminate steadily. Pressing theAdvanceTrac威 with RSC威 “Off”button again will turn

or the speed of the vehicle and trailer is too high. Pull the vehicle-trailerover to a safe location to check the trailer weight distribution and tong

The EPS system has diagnostic checks that continuously monitor theEPS system to ensure proper operation. When a system error isdetected, the following

• Do not fill the power steering pump reservoir above the MAX mark onthe reservoir, as this may result in leaks from the reservoir.If the steering wan

TO STOP ALARM START VEHICLE — Displayed when the perimeteralarm system is armed and the vehicle is entered using the key on thedriver’s side door. In

4. Locate the brake shift interlocklever on the passenger side of theshifter assembly.5. Apply the brake pedal. Using ascrewdriver (or similar tool),

Understanding the gearshift positions of the 6–speed automatictransmission with transmission control switch (if equipped)Your vehicle has been designe

D (Drive) with Grade AssistPressing the transmission control switch on the side of the gearshiftlever activates Grade Assist and cancels Overdrive.Gra

Understanding the gearshift positions of the 6–speed withSelectShift Automatic™ transmission (SST) (if equipped)Your vehicle has been designed to impr

M (Manual) with Grade AssistInitially, moving the lever to M (Manual) activates grade assist andcancels Overdrive.Grade Assist:• Provides additional g

Understanding your SelectShift Automatic™ Transmission (SST)This vehicle is equipped with aSelectShift Automatic™transmission (SST) gearshift lever.SS

The message center display in theinstrument cluster will show thecurrent selected gear you are in.In order to prevent the engine fromrunning at too lo

WARNING: Certain add-on devices such as large trailer hitches,bike or surfboard racks and any device that may block thenormal detection zone of the RS

REARVIEW CAMERA SYSTEM (IF EQUIPPED)The rearview camera system,located on the liftgate, provides avideo image, which appears on thenavigation system s

Use the side mirrors and rearview mirror to get better coverage on bothsides and rear of the vehicle. When shifting out of reverse and into anyother g

AUDIO SYSTEMSNote: If your volume is muted and MYKEY VOLUME LIMITED isdisplayed, refer to MyKey™ in the Locks and Security chapter for moreinformation

Night time and dark area useAt night time or in dark areas, the camera system relies on the reverselamp lighting to produce an image. Therefore it is

Automatic Search for Parking SpaceTo start, press the APA controlswitch (on the console in front ofthe gearshift). The message centerwill display ACTI

Automatic Steering into Parking SpaceAutomatic steering is activated when you stop the vehicle, remove yourhands from the steering wheel and select th

APA FinishedWhen Active Park Assist has completed the automated steering, themessage center displays ACTIVE PARK FINISHED followed by a chime.The driv

TroubleshootingWhy isn’t APA searching for a parking space?• You may have deactivated the AdvanceTrac威 system.• One of the doors (except the driver’s

• One of the parked vehicles has a high altitude attachment (i.e. saltsprayer, snow plow, moving truck high bed, etc.) High altitudeattachments may no

Note: The AWD OFF message may also be displayed in the messagecenter if the AWD system has overheated and defaulted to front wheeldrive. This conditio

sudden return to the pavement which could cause the vehicle to slidesideways out of control or rollover. Remember, your safety and thesafety of others

• In the event of an emergency stop, avoid skidding the tires and do notattempt any sharp steering wheel movements.• If the vehicle goes from one type

If the engine, transmission, AWD system components or axles aresubmerged in water, their fluids should be checked and changed, ifnecessary.Driving thr

Setting the clockTo set the time, press CLOCK. Thedisplay will read SET TIME. Use thememory preset numbers (0–9) toenter in the desired time–hours and

Descend a hill in the same gear youwould use to climb up the hill toavoid excessive brake applicationand brake overheating. Do notdescend in neutral;

Maintenance and ModificationsThe suspension and steering systems on your vehicle have been designedand tested to provide predictable performance wheth

ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside

• towing of your disabled vehicle• emergency travel expense reimbursement• travel planning benefitsIn Canada, for uninterrupted Roadside Assistance co

FUEL PUMP SHUT-OFFIn the event of a moderate to severe collision, this vehicle is equippedwith a fuel pump shut-off feature that stops the flow of fue

Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey — — —3A Violet V

Passenger compartment fuse panelThe fuse panel is located under the instrument panel to the left of thesteering wheel.The fuses are coded as follows.F

Fuse/RelayLocationFuse AmpRatingProtected Circuits8 10A Low beam headlamps (right)9 15A Interior lights, Cargo lamps10 15A Backlighting, Puddle lamps1

Fuse/RelayLocationFuse AmpRatingProtected Circuits32 10A Restraint control module33 10A Not used (spare)34 5A Roll stability control, Refrigeratorrela

WARNING: To reduce risk of electrical shock, always replacethe cover to the power distribution box before reconnecting thebattery or refilling fluid r

Roadside Emergencies 292Getting roadside assistance 292Hazard flasher control 293Fuel pump shut-off 294Fuses and relays 294Changing tires 302Temporary

MEMORY PRESETS (0–9): Whentuned to any station, press and holda preset button until sound returnsand PRESET # SAVED appears in the display. You can sa

Fuse/RelayLocationFuse AmpRatingProtected Circuits9 40A* Anti-lock brake system (ABS)pump10 30A* Starter relay11 30A* Powertrain control module (PCM)r

Fuse/RelayLocationFuse AmpRatingProtected Circuits36 10A** Backup lamps37 10A** PCM run/start38 10A** Trailer tow backup lamps39 Diode Fuel diode40 Di

Fuse/RelayLocationFuse AmpRatingProtected Circuits64 HC micro relay PCM65 G8VA relay A/C clutch66 G8VA relay Fuel pump* Cartridge Fuses ** Mini FusesC

replace it as soon as possible with a road tire/wheel that is the same sizeand type as the road tires and wheels that were originally provided byFord.

• Use snow chains on the end of the vehicle with the dissimilar sparetire/wheelThe usage of a full-size dissimilar spare tire/wheel can lead toimpairm

1. Remove the carpeted floor panellocated in the rear of the vehicle,remove the wing nut that securesthe spare tire by turning itcounterclockwise.2. L

1. Block the diagonally oppositewheel.2. Remove wheel cover (ifequipped) with the lug wrench tipand loosen each wheel lug nutone-half turn countercloc

7. Remove the jack and fully tightenthe lug nuts in the order shown.Refer to Wheel lug nut torquespecifications later in this chapterfor the proper lu

4. Insert the straight end of the jackretention bracket through the eyeletof the angled bracket and swing theretention bracket over the jack. Withthe

TEMPORARY MOBILITY KIT (IF EQUIPPED)Your vehicle may be equipped with atemporary mobility kit (locatedunder the driver’s seat). To removethe temporary

CD/MP3 PlayerCD: Press to enter CD/MP3 mode. Ifa disc is already loaded into thesystem, CD/MP3 play will beginwhere it ended last. If no CD is loaded,

1. Air compressor (inside)2. Diverter knob3. On/Off switch4. Air pressure gauge5. Sealant bottle/canister6. Sealant filling clear tube7. Sealant tube

• Read the information in the Tips for use of the temporary mobilitykit section to ensure safe operation of the temporary mobility kit andyour vehicle

• Operating the temporary mobility kit could cause an electricaldisturbance in radio and DVD player operation.What to do when a tire is puncturedA tir

4. Plug the power cable into the 12Vpower point in the vehicle.5. Remove the warning sticker found on the canister and place it on thetop of the instr

Note: When the sealing compound is first added into the tire, theair pressure gauge reading on the compressor unit may indicate ahigher value; this is

3. Turn the dial clockwise to the air position. Turn on the kit by pressingthe on/off button.4. Adjust the tire to therecommended inflation pressurefr

Removal of the Sealant Canister from the Temporary Mobility Kit1. Unwrap the clear tube from thecompressor housing.2. Locate the yellow cap at the end

Installation of the Sealant Canister to the Temporary MobilityKit1. Align the sealant canister withthe temporary mobility kit housing.2. Once aligned,

Note: If you experience any difficulties with the removal or installationof the sealant canister, consult your Ford Motor Company authorizeddealer for

Note: Inspect the wheel pilot holeprior to installation. If there isvisible corrosion in wheel pilot hole,remove loose particles by wipingwith clean r

SEEK: Press SEEK toaccess the previous/next track.CAT (Category) / FOLD(Folder):In MP3 mode only– PressCAT/FOLD and thenpressSEEK to access the previo

Preparing your vehicleWhen the battery is disconnected or a new battery is installed, theautomatic transmission must relearn its shift strategy. As a

2. Connect the other end of the positive (+) cable to the positive (+)terminal of the assisting battery.3. Connect the negative (-) cable to the negat

4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarbureto

Removing the jumper cablesRemove the jumper cables in the reverse order that they wereconnected.1. Remove the jumper cable from the ground metal surfa

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of

WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y

If the vehicle is towed by other means or incorrectly, vehicledamage may occur.Ford Motor Company produces a towing manual for all authorized towtruck

GETTING THE SERVICES YOU NEEDWarranty repairs to your vehicle must be performed by an authorizedFord, Lincoln, or Mercury dealer. While any authorized

In Canada:Mailing address (Ford vehicles)Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4Teleph

In the United States, a warranty dispute must be submitted to the BBBAUTO LINE before taking action under the Magnuson-Moss WarrantyAct, or to the ext

Satellite Radio (if equipped)Satellite radio is available only with a valid SIRIUS radiosubscription. Check with your authorized dealer for availabili

procedure outlined on the first page of the Customer Assistance section,you may be eligible to participate in the BBB AUTO LINE program.The BBB AUTO L

The CAMVAP program is a straight-forward and relatively speedyalternative to resolve a disagreement when all other efforts to produce asettlement have

If you are in another foreign country, contact the nearest authorizeddealer. If the authorized dealer employees cannot help you, they candirect you to

REPORTING SAFETY DEFECTS (U.S. ONLY)If you believe that your vehicle hasa defect which could cause a crashor could cause injury or death, youshould im

WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft威 Detail Wash (ZC-3-A), which i

WAXING• Wash the vehicle first.• Do not use waxes that contain abrasives; use Motorcraft威 PremiumLiquid Wax (ZC-53-A), which is available from your au

ENGINEEngines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing:• Take care when

3.5L V6 engineCleaning3372010 Flex (471)Owners Guide, 1st PrintingUSA (fus)

3.5L V6 EcoBoost enginePLASTIC (NON-PAINTED) EXTERIOR PARTSUse only approved products to clean plastic parts. These products areavailable from your au

• The wiper blades can be cleaned with isopropyl (rubbing) alcohol orMotorcraft威 Premium Windshield Washer Concentrate (ZC-32-A),available from your a

TEXT: Press and release to displaythe artist and song title. While inTEXT MODE, press again to scrollthrough the Artist (AR), Song (SO), Channel (CH)

If a staining liquid like coffee/juice has been spilled on the instrumentpanel or on interior trim surfaces, clean as follows:1. Wipe up spilled liqui

LEATHER SEATS (IF EQUIPPED)Your leather seating surfaces have a clear, protective coating over theleather.• For routine cleaning, wipe the surface wit

Motorcraft威 Premium Glass Cleaner (Canada only) (CXC-100)Motorcraft威 Premium Liquid Wax (ZC-53-A)Motorcraft威 Premium Windshield Washer Concentrate (U.

SERVICE RECOMMENDATIONSTo help you service your vehicle, we provide scheduled maintenanceinformation which makes tracking routine service easy.If your

OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel nearthe steering column.2. Go to th

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT3.5L V6 engine1. Power steering fluid reservoir2. Engine coolant reservoir3. Brake fluid reservoir4. B

3.5L V6 EcoBoost engine1. Engine coolant reservoir2. Brake fluid reservoir3. Battery4. Power distribution box5. Air filter assembly6. Automatic transm

Engine shieldSome vehicles may be equippedwith an aero-shield under theengine. This shield needs to beremoved for service, including oiland filter cha

CHANGING THE WIPER BLADES1. Pull the wiper arm away from thevehicle. Turn the blade at an anglefrom the wiper arm. Press the locktab to release the bl

4. Attach the new wiper to thewiper arm and press it into placeuntil a click is heard.If you find this procedure toodifficult, please see your dealer.

titles, the display will read REPLACE SONG? Press OK to access thesaved titles and pressSEEK to cycle through the saved titles.When the song title app

• If the oil level is below thismark, engine oil must be addedto raise the level within thenormal operating range.• If required, add engine oil to the

Engine oil and filter recommendationsLook for this certificationtrademark.Use SAE 5W-20 engine oilOnly use oils “Certified For Gasoline Engines” by th

BATTERYYour vehicle is equipped with aMotorcraft威 maintenance-freebattery which normally does notrequire additional water during itslife of service.If

WARNING: Keep batteries out of reach of children. Batteriescontain sulfuric acid. Avoid contact with skin, eyes or clothing.Shield your eyes when work

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recyclin

When the engine is cold, check thelevel of the engine coolant in thereservoir.• The engine coolant should be at the FULL COLD level or within theCOLD

• Do not mix coolants. Add the coolant type originally equippedin your vehicle. Refer to Maintenance product specifications andcapacities in this chap

4. When you are sure that all the pressure has been released, use thecloth to turn it counterclockwise and remove the cap.5. Fill the coolant reservoi

• NEVER increase the coolant concentration above 60%.• Increased engine coolant concentrations above 60% willdecrease the overheat protection characte

and other factors. If this occurs, there is no need to pull off the road.The vehicle can continue to be driven while this message is active.WARNING: T

b. CHANGE PIN: Press OK when CHANGE PIN is displayed. Thedisplay will read ENTER OLD PIN. Enter your current (old) PINnumber and when the system accep

How fail-safe cooling worksIf the engine begins to overheat:• The engine coolant temperature gauge will move to the red (hot)area.• The coolant temper

FUEL FILTERYour vehicle is equipped with a lifetime fuel filter that is integrated withthe fuel tank. Regular maintenance or replacement is not needed

• Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes,remove contact lenses (if worn), flush with water for 15 minutes andseek med

Use the following guidelines to avoid electrostatic charge build-up whenfilling an ungrounded fuel container:• Place approved fuel container on the gr

immediately. It may take several driving cycles for the check fuel fill inletlamp or CHECK FUEL FILL INLET message to turn off. A driving cycleconsist

rating of 91 or higher is recommended. The performance gained by usingpremium fuel will be most noticeable in hot weather or in severe dutyapplication

If you have run out of fuel:• You may need to cycle the ignition from off to on several times afterrefueling to allow the fuel system to pump the fuel

2. Slowly insert the funnel into theEasy Fuel™ system.3. Fill the vehicle with fuel from the portable fuel container.4. When done, clean the funnel or

The amount of usable fuel in the empty reserve varies and shouldnot be relied upon to increase driving range. When refueling yourvehicle after the fue

Driving style — good driving and fuel economy habitsGive consideration to the lists that follow and you may be able to changea number of variables and

Extra FeaturesAUX: Press repeatedly to cyclethrough LINE (auxiliary audiomode), SYNC威 (if equipped) andFES modes (if equipped).For location and furthe

• Carrying unnecessary weight may reduce fuel economy (approximately1 mpg [0.4 km/L] is lost for every 400 lb [180 kg] of weight carried).• Adding cer

emission control, such non-Ford parts should be equivalent to genuineFord Motor Company parts in performance and durability.WARNING: Do not park, idle

3. The fuel fill inlet may not have been properly closed. See Easy Fuel™“no cap” fuel system in this chapter.4. Driving through deep water—the electri

The OBD-II system is designed to check the emission control systemduring normal driving. A complete check may take several days. If thevehicle is not

BRAKE FLUIDThe fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the MIN andMAX

6. Install the dipstick making sure it is fully seated in the filler tube.7. Remove the dipstick and inspect the fluid level. The fluid should be inth

Use of a non-approved automatic transmission fluid may causeinternal transmission component damage.If necessary, add fluid in 1/2 pint(250 ml) increme

Changing the air filter element3.5L V63.5L V6 (EcoBoost)1. Release the clamps that secure the air filter housing cover.2. Carefully separate the two h

6. Replace the air filter housingcover and secure the clamps. Besure that the air cleaner cover tabsare engaged into the slots of the aircleaner housi

MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItems CapacityFord Part Name orequivalentFord Part Number /Ford SpecificationBrake fluidBetween MAX a

The Auxiliary Input Jack provides away to connect your portable musicplayer to the in-vehicle audiosystem. This allows the audio from aportable music

Items CapacityFord Part Name orequivalentFord Part Number /Ford SpecificationEngine oil(3.5L V6 engine)5.5 quarts (5.2L)•Motorcraft威 SAE 5W-20Premium

Items CapacityFord Part Name orequivalentFord Part Number /Ford SpecificationPower steering fluid(except EcoBoostengine)Between MAX andMIN on reservoi

ENGINE DATAEngine 3.5L V6 engine 3.5L V6 EcoBoost engineCubic inches 214 214FuelSee Octanerecommendationsearlier in this chapter.See Octanerecommendat

3.5L V6 EcoBoost engineIDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations requ

Vehicle identification number (VIN)The vehicle identification number islocated on the driver sideinstrument panel.Please note that in the graphic,XXXX

TRANSMISSION CODE DESIGNATIONSYou can find a transmission code onthe Safety Compliance CertificationLabel. The following table tells youwhich transmis

GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of

Peace of mindRemote startLocking fuel plug for capless fuel systemsCargo area protectorWheel locksFor maximum vehicle performance, keep the following

FORD ESP EXTENDED SERVICE PLANSMore than 30 million Ford, Lincoln, and Mercury owners have discoveredthe powerful protection of Ford ESP. It is the on

Ford ESP Can Quickly Pay for ItselfOne service bill – the cost of parts and labor – can easily exceed theprice of your Ford ESP Service Contract. With

Troubleshooting:1. Do not connect the audio input jack to a line level output. Line leveloutputs are intended for connection to a home stereo and are

Ford Extended Service Plan3902010 Flex (471)Owners Guide, 1st PrintingUSA (fus)

AAccessory delay ...102Active Park Assist ...280AdvanceTrac ...262Air cleaner filter

Child safety seats ...203in front seat ...204in rear seat ...204LATCH ...

Engine ...382cleaning ...336coolant ...354fail-

Homelink wireless controlsystem ...110Hood ...344IIgnition ...

OOctane rating ...364Oil (see Engine oil) ...349Overdrive ...270PParental MyKe

Satellite Radio Information ...43Seats ...151child safety seats ...203climate control ...

VVehicle Identification Number(VIN) ...384Vehicle loading ...242Ventilating your vehicle

Accessories 386Ford Extended Service Plan 388Index 391All rights reserved. Reproduction by any means, electronic or mechanicalincluding photocopying,

Your vehicle may be equipped with aUSB port inside your center console.This feature allows you to plug inmedia playing devices, memorysticks, and also

CD/CD player careDo:• Handle discs by their edges only.(Never touch the playingsurface).• Inspect discs before playing.• Clean only with an approved C

CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommen

Sample MP3 structureIf you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variou

• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere w

Radio Display Condition Action RequiredACQUIRING Radio requires morethan two seconds toproduce audio forthe selectedchannel.No action required. Thisme

Radio Display Condition Action RequiredNO TEXT Categoryinformation notavailable.Category information notavailable at this time onthis channel. The sys

Quick startYour family entertainment system includes two headrest-mounted DVDplayer/screens, two sets of wireless infrared (IR) headphones and awirele

To play a CD or MP3 discThe DVD system can play audio CDs, CD-R and CD-R/W, CD-ROM. Toensure proper disc operation, check the disc for finger prints a

• USB port (4): To access, ensure that the monitor is already selectedas the media source (Monitor A or Monitor B.) Then, plug in yourflash/thumb driv

CONGRATULATIONSCongratulations on acquiring your new Ford Motor Company product.Please take the time to get well acquainted with your vehicle by readi

DVD player controls1./ (Play/Pause): Press to play or pause a CD, DVD orflash/thumb drive track.2.(Stop): Press to stop the current DVD, CD/MP3, or fl

5. / (Headphones/Speakers): Press to activate dual play mode oneither headrest system. During dual play mode, the following happens:a. Rear speakers t

Remote controlUnless otherwise stated, all operations can be carried out with theremote control. Always point the remote control directly at the playe

4. RETURN: Press to return to the previous menu screen.5. SETUP: Press to access the setup menu for each monitor. Refer toSetup Menu later in this sec

15. MEDIA for Monitor A: In Dual Play mode, press MEDIA repeatedlyto select from the possible media sources: (Monitor A, Monitor B, AM,FM1, FM2, SR1,

Battery replacementBatteries are supplied with theremote control unit. Since allbatteries have a limited shelf life,replace them when the unit fails t

To install the batteries, removethe screw on the cover and removethe cover. Then, gently lift the topof the cover away from the housingto expose the b

Ensure that the headphones are turned off when not in use. Afterapproximately one minute of not being in use (no infrared signal isreceived), the wire

Dual Play: Dual play is when the rear seat passengers choose to listento a different playing media than the front seat passengers. With theDVD and rea

Radio interaction: If your vehicle is equipped with a non-touchscreenaudio system, you can press AUX on the radio repeatedly until DVDappears in the d

Protecting the environmentWe must all play our part inprotecting the environment. Correctvehicle usage and the authorizeddisposal of waste, cleaning a

Aspect ratio (TV display type)This screen allows you to select theviewing size and shape of the videodisplayed on the LCD screen. This isdisc dependen

1. Press SETUP on the remote to access the menu options.2. Press/ to ’highlight’ the monitor icon. (A disc will appearbeneath the icon signifying it i

Speaker setupThis screen allows you to adjust theaudio balance for your speakers. Toaccess:1. Press SETUP on the remote to access the menu options.2.

4. Press / to chose from Sharpness, Brightness, contrast, color(gamma), hue, saturation and luma-delay.General setup — screen exitTo exit the setup sc

General informationNote: DVDs are formatted byregions. US and Canada systems canonly play region 1 DVDs and Mexicosystems can only play region 4DVDs.

Read all of the safety and operating instructions before operating thesystem and retain for future reference.Do not attempt to service, repair or modi

Federal Communication Commission (FCC) ComplianceChanges or modifications not approved by Ford Lincoln-Mercury couldvoid user’s authority to operate t

Foreign substancesExercise care to prevent dirt and foreign objects from entering the DVDplayer compartment. Be especially careful not to spill liquid

SINGLE ZONE CLIMATE CONTROL WITH REAR PASSENGERCOMPARTMENT CLIMATE CONTROL1.Defrost: Distributes outside air through the windshield defrostervents and

4. A/C: Press to activate/deactivate air conditioning. Use withrecirculated air to improve cooling performance and efficiency. A/Cengages automaticall

Special instructionsFor your added safety, your vehicle is fitted with sophisticated electroniccontrols.WARNING: Please read the section Airbag Supple

Operating tips• To reduce fog build up on the windshield during humid weather, placethe air flow selector in theposition.• To reduce humidity build up

DUAL ZONE AUTOMATIC TEMPERATURE CONTROL WITHHEATED SEATS AND REAR PASSENGER COMPARTMENTCLIMATE CONTROL (IF EQUIPPED)Temperature conversion: To switch

• : Distributes air through the instrument panel vents.•: Distributes air through the instrument panel vents, floor ventsand rear seat floor vents.•:

10. Power/Cabin temperature: Press to activate/deactivate theclimate control system. When the system is off, outside air is preventedfrom entering the

DUAL ZONE AUTOMATIC TEMPERATURE CONTROL(NAVIGATION BASED–IF EQUIPPED)Temperature conversion: To switch between Fahrenheit and Celsius,refer to Message

5. Passenger heated seat (if equipped): Press to control thepassenger heated seat. Refer to Heated seats in the Seating and SafetyRestraints chapter f

TOUCHSCREEN FUNCTIONSTemperature conversion: To switch between Fahrenheit and Celsius,refer to Message center in the Driver Controls chapter.Front Zon

Max A/C– Distributes recirculated air through the instrument panelvents to cool the vehicle. This re-cooling of the interior air is moreeconomical and

In manual override mode, select or , A/C and recirculatedairand set the temperature to 60°F (16°C). Set the fan to thehighest speed initially, then ad

6. Rear Passenger side heated seat control (if equipped): Pressto heat the seat. Refer to Heated seats in the Seating and SafetyRestraints chapter for

• how fast the vehicle was traveling;• where the driver was positioning the steering wheel; and• longitude and latitude of vehicle at last location, u

HEADLAMP CONTROLTurns the lamps off.Turns on the parking lamps,instrument panel lamps, licenseplate lamps and tail lamps.Turns the low beam headlampso

3. Turn the ignition switch to on and then back to off.4. Turn the headlamp control to the autolamp position. The headlampswill turn on.5. Wait the de

Daytime running lamps (DRL) (if equipped)Turns the headlamps on with a reduced output.To activate:• the ignition must be in the on position,• the head

Vertical aim adjustment1. Park the vehicle directly in front of a wall or screen on a level surface,approximately 25 feet (7.6 meters) away.• (1) 8 fe

Halogen headlamp5. Locate the vertical adjuster on each headlamp. Using a Phillips #2screwdriver, turn the adjuster either clockwise (to adjust down)

INTERIOR LAMPSDome lamps and map lampsThe map lamps are located on theoverhead console. Press the controlson either side of each map lamp toturn on th

Note: The ambient lights will stay on until the ignition is placed in theoff position and either of the front doors are opened or the accessorydelay t

Function Number of bulbsTradenumberFront park/turn lamp 2 3157NA*Front sidemarker lamp N/A LEDHeadlamp2 9008 H132D3 HID(optional)Tail/brake/turn signa

3. Locate the high beam/low beamheadlamp bulb electrical connectorand remove it by squeezing thelocking tab and pulling it straightout.4. Remove the b

Replacing rear stop/park/turn/backup and side marker lamp bulbs(non LED)The stop/tail/turn/backup and side marker lamp bulbs are located in thetail la

CELL PHONE USEThe use of Mobile Communications Equipment has become increasinglyimportant in the conduct of business and personal affairs. However,dri

Replacing fog lamp bulbs (if equipped)1. Make sure the fog lamp switch isin the off position.2. From underneath the vehicle,partially remove the tire

MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the

Rear window wiper/washer controlsFor rear wiper operation, rotate therear window wiper and washercontrol to the desired position.Select:2 — Normal spe

ILLUMINATED VISOR MIRRORLift the mirror cover to turn on thevisor mirror lamp.Slide on rod featureThe visor will slide back and forthon the rod for in

OVERHEAD CONSOLEThe appearance of your vehicle’s overhead console will vary according toyour option package.Storage compartmentThe storage compartment

Compass zone adjustment1. Determine which magnetic zoneyou are in for your geographiclocation by referring to the zonemap.2. Turn ignition to the on p

2. To calibrate, press and hold the 7and 9 radio preset buttons togetherfor approximately 10 seconds untilCAL appears. Release the buttons.3. Slowly d

Second row center console features (if equipped)The second row center consoleincorporates the following features:• Flip forward armrest to provide afl

Refrigerator: Briefly press andhold the COOL side of thecontrol.The indicator light on thecool side of the switch willilluminate and the indicator lig

Auxiliary power points can be found in the following locations:• Near the floor in the front console bin on the passenger’s side• In the center consol