Ford 2001 Explorer Sport Trac Manuale Utente

Before drivingIntroduction 2Instrumentation 6Controls and features 18Seating and safety restraints 96Starting and drivingStarting 127Driving 132Roadsi

Air bag readinessMomentarily illuminates when theignition is turned ON. If the lightfails to illuminate, continues to flashor remains on, have the sys

Folding down rear 60/40 seats1. Raise the rear seat head restraint.2. Flip the bottom of the headrestraint up, toward the front seat.3. While holding

5. Push the seatback toward thefront seat and completely downuntil it locks into place.A carpeted panel will flip down fromthe back panel to complete

SAFETY RESTRAINTSSafety restraints precautionsAlways drive and ride with your seatback upright and the lapbelt snug and low across the hips.To reduce

Always transport children 12 years old and under in the backseat and always properly use appropriate child restraints.Energy Management Feature• This

2. To unfasten, push the releasebutton and remove the tongue fromthe buckle.The front and rear outboard safety restraints in the vehicle arecombinatio

How to use the automatic locking mode• Buckle the combination lap andshoulder belt.• Grasp the shoulder portion andpull downward until the entirebelt

After any vehicle collision, the front passenger outboard seat beltsystem must be checked by a qualified technician to verify thatthe “automatic locki

Lap beltsAdjusting the lap beltThe lap belt should fit snugly and as low as possible around thehips, not across the waist.• 2nd row center seating pos

Conditions of operationIf... Then...The driver’s safety belt is notbuckled before the ignition switchis turned to the ON position...The safety belt wa

The following are reasons most often given for not wearing safety belts:(All statistics based on U.S. data)Reasons given... Consider...“Crashes are ra

Turn signalIlluminates when the left or rightturn signal or the hazard lights areturned on. If one or both of theindicators stay on continuously orfla

One time disableAny time the safety belt is buckled and then unbuckled during an ignitionON cycle, Belt Minder will be disabled for that ignition cycl

6. Within seven seconds of the safety belt warning light turning off,buckle then unbuckle the safety belt.• This will disable Belt Minder if it is cur

AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)Your vehicle is equipped with a crash sensing and diagnostic modulewhich records information about the air

All occupants of the vehicle, including the driver, should alwaysproperly wear their safety belts, even when an air bag SRS isprovided.Always transpor

Additional equipment may affect the performance of the air bagsensors increasing the risk of injury. Please refer to the BodyBuilders Layout Book for

How does the air bag supplemental restraint system work?The air bag SRS is designed toactivate when the vehicle sustainslongitudinal deceleration suff

The air bags inflate and deflaterapidly upon activation. After air bagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burn

If the air bag has deployed, the air bag will not functionagain and must be replaced immediately. If the air bag is notreplaced, the unrepaired area w

Important child restraint precautionsYou are required by law to use safety restraints for children in the U.S.and Canada. If small children ride in yo

A belt-positioning booster seat should be used if the shoulder belt restsin front of the child’s face or neck, or if the lap belt does not fit snuglyo

Four wheel drive low (if equipped)Momentarily illuminates after theengine is STARTED. Illuminateswhen four-wheel drive low isengaged. If the light con

When installing a child safety seat:• Review and follow the informationpresented in the Air BagSupplemental Restraint System(SRS) section in this chap

Installing child safety seats in combination lap and shoulder beltseating positionsAir bags can kill or injure a child in a child seat. NEVER place ar

3. While holding the shoulder andlap belt portions together, route thetongue through the child seataccording to the child seatmanufacturer’s instructi

7. Pull the lap belt portion acrossthe child seat toward the buckle andpull up on the shoulder belt whilepushing down with your knee on thechild seat.

5. If you have not pulled out enough webbing to reach, allow thewebbing to fully retract before attempting to pull it out again and repeatsteps 2 thro

1. Position the child safety seat on the rear seat cushion.2. Route the child safety seat tether strap over the back of the seat.For vehicles with adj

4. Slide open the tether anchorcover.5. Clip the tether strap to theanchor and return the seat back toits locked position.If the tether strap is clipp

PREPARING TO START YOUR VEHICLEEngine starting is controlled by the powertrain control system. Thissystem meets all Canadian Interference-Causing Equi

2. Make sure the headlamps and vehicle accessories are off.• Make sure the parking brake isset.• Make sure the gearshift is in P(Park).3. Turn the key

Make sure the corresponding lights illuminate or illuminate briefly. If alight fails to illuminate, have the vehicle serviced.• If the driver’s safety

Speed controlThis light comes on when either theSET/ACCEL or RESUME controlsare pressed. It turns off when thespeed control OFF control ispressed, the

–18 degrees C (0 degrees F). If you experience this condition you mayfind that a different brand of winter grade (Ed85) (if available in yourarea) imp

Guarding against exhaust fumesAlthough odorless and colorless, carbon monoxide is present in exhaustfumes. Take precautions to avoid its dangerous eff

BRAKESYour service brakes are self-adjusting. Refer to the scheduledmaintenance guide for scheduled maintenance.Occasional brake noise is normal and o

ABS warning lampABSTheABSwarning lamp in the instrument cluster momentarily illuminateswhen the ignition is turned to the ON position. If the light do

The BRAKE warning lamp in theinstrument cluster illuminates andremains illuminated (when theignition is turned ON) until theparking brake is released.

If the steering wanders or pulls, the condition could be caused by any ofthe following:• underinflated tire(s) on any wheel(s)• uneven vehicle loading

Vehicles with a higher center of gravity such as utility andfour-wheel drive vehicles handle differently than vehicles with alower center of gravity.

Do not drive your vehicle until you verify that the brakelampsare working.If your vehicle gets stuck in mud or snow it may be rocked out byshifting be

Understanding gearshift positionsHold the brake pedal down while you move the gearshift leverfrom P (Park) to another position. If you do not hold the

(Overdrive) can be deactivatedby pressing the transmission controlswitch on the end of the gearshiftlever.The transmission control indicatorlight (TCI

GAUGESSpeedometerIndicates the current vehicle speed.!C123456RPMx1000ABSCHECKENGINEEFHHHPRN D 2 1THEFTSPEEDCONT4WDHIGH4WDLOWO/DOFFMPH20604080km/h00120

1 (First)Use 1 (First) to provide maximumengine braking on steepdowngrades. Upshifts can be madeby shifting to 2 (Second) or to(Overdrive). Selecting

Recommended shift speedsUpshift according to the following charts for best fuel economy:Upshifts when accelerating (recommended for best fuel economy)

2. Engage the parking brake.3. Shift into 1 (First).4. Turn the ignition to Off.Do not park your vehicle in Neutral, it may move unexpectedlyand injur

4WD system indicator lightsThe 4WD system indicator lights illuminate only under the followingconditions. If these lights illuminate when driving in 2

Shifting from 4X4 HIGH (4WD high) to 2WD (2WD high)Move the 4WD control to 2WDposition at any forward speed.• You do not need to operate thevehicle in

4. Move the 4WD control to the2WD position.5. Wait for the 4WD low indicatorlight to turn off.Shifting between 4X4 HIGH (4WD high) and 4X4 LOW (4WD lo

If your vehicle gets stuckIf the vehicle is stuck it may be rocked out by shifting from forward andreverse gears, stopping between shifts, in a steady

Replace rear axle lubricant any time the axle has been submerged inwater. The rear axle does not normally require a lubricant change for thelife of th

VEHICLE LOADINGBefore loading a vehicle, familiarize yourself with the following terms:• Base Curb Weight: Weight of the vehicle including any standar

Do not exceed the GVWR or the GAWR specified on thecertification label.Do not use replacement tires with lower load carrying capacities than theorigin

Engine coolant temperature gaugeIndicates the temperature of theengine coolant. At normal operatingtemperature, the needle remainswithin the normal ar

Calculating the load your vehicle can carry/tow1. Use the appropriate maximum gross combined weight rating (GCWR)chart to find the maximum GCWR for yo

Follow these guidelines to ensure safe towing procedure:• Stay within your vehicle’s load limits.• Thoroughly prepare your vehicle for towing. Refer t

4x2 w/manual transmissionGCWR (Gross Combined Weight Rating)/Trailer weightsEngineRearaxleratioMaximumGCWR-kg(lbs.)Trailer WeightRange-kg(lbs.)0-Maxim

4x4 w/manual transmissionGCWR (Gross Combined Weight Rating)/Trailer WeightsEngineRearaxleratioMaximumGCWR - kg(lbs.)Trailer WeightRange(0-Maximum)- k

Safety chainsAlways connect the trailer’s safety chains to the frame or hook retainersof the vehicle hitch. To connect the trailer’s safety chains, cr

Driving while you towWhen towing a trailer:• Ensure that you turn off your speed control. The speed control mayshut off automatically when you are tow

Launching or retrieving a boatWhen backing down a ramp during boat launching or retrieval:• do not allow the static water level to rise above the bott

If a distance of 80 km (50 miles) or a speed of 56 km/h (35 mph)must be exceeded, you must disconnect the driveshaft. Fordrecommends the driveshaft be

Getting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program

Roadside coverage beyond basic warrantyIn the United States, you may purchase additional roadside assistancecoverage beyond this period through the Fo

TachometerIndicates the engine speed inrevolutions per minute.Driving with your tachometerpointer continuously at the top ofthe scale may damage the e

The fuel pump shut-off switch islocated in the passenger’s foot well,by the kick panel.Use the following procedure to reset the fuel pump shut-off swi

FUSES AND RELAYSFusesIf electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinth

Passenger compartment fuse panelThe fuse panel is located on theleft-hand side of the instrumentpanel facing the driver’s side door.Pull the panel cov

Fuse/RelayLocationFuse AmpRatingPassenger Compartment Fuse PanelDescription1 5A Power Mirror Switch2 5A Aux. High Mount Stop Lamp3 7.5A Left Stop/Turn

Fuse/RelayLocationFuse AmpRatingPassenger Compartment Fuse PanelDescription20 7.5A Generic Electronic Module (GEM), Radio,Moonroof Relay, Power Window

Power distribution boxThe power distribution box islocated in the engine compartment.The power distribution box containshigh-current fuses that protec

The high-current fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingPower Distribution Box Description1 50A** Fuse Panel2 — Not Used3 30A** Po

Fuse/RelayLocationFuse AmpRatingPower Distribution Box Description17 — Not Used18 — Not Used19 — Not Used20 — Not Used21 10A* PCM Memory22 15A* Horn23

Fuse/RelayLocationFuse AmpRatingPower Distribution Box Description46B — Front Washer Pump Relay47A 20A* Windows/Roof47B — Not Used48 — Window Safety R

Location of the spare tire and toolsThe spare tire and tools for your vehicle are stowed in the followinglocations:Tool LocationSpare tire Under the v

Fuel gaugeDisplays approximately how muchfuel is in the fuel tank (when thekey is in the ON position). The fuelgauge may vary slightly when thevehicle

2. Insert the jack handle into theopening just above the rear bumper.The handle will stop moving forwardand resistance to turning will be feltwhen pro

Tire change procedureWhen one of the front wheels is off the ground, the transmissionalone will not prevent the vehicle from moving or slipping off th

4. Insert tapered end of the lug nutwrench to remove any wheel trim.5. Loosen each wheel lug nutone-half turn counterclockwise butdo not remove them u

• RearTo lessen the risk ofpersonal injury, do not putany part of your body under thevehicle while changing a tire. Donot start the engine when yourve

11. Remove the jack and fullytighten the lug nuts in the ordershown.12. Stow the flat tire. Refer toStowing the spare tire.13. Stow the jack and lug n

4. Check all battery terminals and remove any excessive corrosion beforeyou attach the battery cables. Ensure that vent caps are tight and level.5. Tu

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable to an ex

• 4.0L SOHC V6 Engine5. Ensure that the cables are clear of fan blades, belts, moving parts ofboth engines, or any fuel delivery system parts.Jump sta

• 4.0L SOHC V6 Engine2. Remove the jumper cable on the negative (-) connection of thebooster vehicle’s battery.+–+–+–+–Roadside emergencies178

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of

HEADLAMP CONTROLRotate the headlamp control to thefirst position to turn on the parkinglamps. Rotate to the second positionto also turn on the headlam

WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member, your roadside assistance center.It

If the vehicle is towed by other means or incorrectly, vehicledamage may occur.Special Conditions:• Release the parking brake.• Turn the ignition to t

SERVICE RECOMMENDATIONSTo help you service your vehicle:• We highlight do-it-yourself items in the engine compartment for easylocation.• We provide a

Note: Do not start your engine with the air cleaner removed and do notremove it while the engine is running.OPENING THE HOOD1. Inside the vehicle, pul

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT4.0L SOHC V6 engine1. Windshield washer fluid reservoir2. Automatic transmission fluid dipstick (if eq

ENGINE OILChecking the engine oilRefer to the scheduled maintenance guide for the appropriate intervalsfor checking the engine oil.1. Make sure the ve

• If the oil level is below the ADDmark or MIN mark, add enoughoil to raise the level within theADD-FULL range or MIN-MAXrange.• Oil levels above the

Engine oil and filter recommendationsLook for this certificationtrademark.SAE 5W-30 engine oil recommendedOnly use oils “Certified For Gasoline Engine

BRAKE FLUIDChecking and adding brake fluidBrake fluid should be checked andrefilled as needed. Refer to thescheduled maintenance guide forthe service

CLUTCH FLUID (IF EQUIPPED)Check the fluid level. Refer to the scheduled maintenance guide for theservice interval schedules.During normal operation, t

High beams• Push forward to activate.• Pull toward you to deactivate.Flash to passPull toward you to activate andrelease to deactivate.PANEL DIMMER CO

WINDSHIELD WASHER FLUIDWasher fluidCheck the washer fluid wheneveryou stop for fuel. The reservoir ishighlighted with asymbol.If the level is low, add

ENGINE COOLANTChecking engine coolantThe concentration and level of engine coolant should be checked at themileage intervals listed in the scheduled m

• Refer to the Scheduled Maintenance Guide for service intervalschedules.• Be sure to read and understand Precautions when servicing yourvehicle in th

with the factory-filled coolant. Mixing Motorcraft Speciality OrangeEngine Coolant or any orange-colored extended life product with yourfactory filled

5. Fill the coolant reservoir slowly with the proper coolant mixture (seeabove), to within the “cold fill range” or the “cold full” level on thereserv

Coolant refill capacityTo find out how much fluid your vehicle’s cooling system can hold, referto Refill capacities in the Capacities and specificatio

CHECKING AND ADDING POWER STEERING FLUIDCheck the power steering fluid.Refer to the scheduled maintenanceguide for the service intervalschedules. If a

operated for an extended period at high speeds, in city traffic during hotweather or pulling a trailer, the vehicle should be turned off for about 30m

The transmission fluid should be inthis range if at ambient temperature(10°C-35°C [50°F-95°F]).High fluid levelFluid levels above the safe rangemay re

Checking and adding transfer case fluid (if equipped)1. Clean the filler plug.2. Remove the filler plug andinspect the fluid level.3. Add only enough

The following warning may be required by California law:CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain

CLIMATE CONTROL SYSTEMManual heating and air conditioning system (if equipped)Fan speed controlControls the volume of air circulatedin the vehicle.Tem

BATTERYYour vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice.How

When lifting a plastic-cased battery, excessive pressure on theend walls could cause acid to flow through the vent caps,resulting in personal injury a

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recyclin

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADINGNew vehicles are fitted with tiresthat have a rating on them calledTire Quality Grades. The Qualitygrade

The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not includeacceleration, cornering, hydroplaning o

Tire rotationBecause your vehicle’s tires perform different jobs, they often weardifferently. To make sure your tires wear evenly and last longer, rot

• Five tire rotationReplacing the tiresReplace the tires when the wearband is visible through the tiretreads.When replacing full size tires, never mix

Make sure that all replacement tires are of the same size, type,load-carrying capacity and tread design (e.g., “All Terrain”, etc.),as originally offe

• Do not exceed 48 km/h (30 mph) with tire cables or chains on yourvehicle.Consult your dealer for information on other Ford approved methods oftracti

Observe the following guidelines when handling automotive fuel:• Extinguish all smoking materialsand any open flames beforefueling your vehicle.• Alwa

• A/C-Uses outside air to cool the vehicle. It is quieter than MAX A/Cbut not as economical. Airflow will be from the instrument panelregisters.•(Pane

Pure ethanol is the alcohol which is the intoxicating agent in liquor, beerand wine. It is distilled from the fermentation of plants such as field cor

Use the following guidelines to avoid static build-up when filling anungrounded fuel container:• Place approved fuel container on the ground.• DO NOT

FFV engine (if equipped)Your vehicle is designed to use Fuel Ethanol(E85), “Regular” unleadedgasoline or any percentage of the two fuels combined.U.S.

FFV engine (if equipped)Your FFV will operate well on ordinary “Regular” unleaded gasoline, butonly the highest quality fuel ethanol will provide the

Fuel Filler CapYour fuel tank filler cap has an indexed design with a 1/8 turn on/offfeature.When fueling your vehicle:1. Turn the engine off.2. Caref

Fuel FilterFor fuel filter replacement, see your dealer or a qualified servicetechnician. Refer to the scheduled maintenance guide for the appropriate

• Allow no more than 2 automatic click-offs when filling.• Always use fuel with the recommended octane rating.• Use a known quality gasoline, preferab

Habits• Smooth, moderate operation can yield up to 10% savings in fuel.• Steady speeds without stopping will usually give the best fueleconomy.• Idlin

• Adding certain accessories to your vehicle (for example bugdeflectors, rollbars/light bars, running boards, ski/luggage racks) mayreduce fuel econom

The scheduled maintenance items listed in the scheduled maintenanceguide are essential to the life and performance of your vehicle and to itsemissions

• To reduce humidity buildup inside the vehicle in cold weatherconditions, don’t drive with the climate control system in the OFF orMAX A/C position.•

Readiness for Inspection/Maintenance (I/M) testingIn some localities, it may be a legal requirement to pass an I/M test ofthe on-board diagnostics sys

Replacing headlamp bulbsTo remove the headlamp bulb:1. Make sure headlamp switch is inOFF position, then lift hood and liftthe plastic headlamp cover.

1. With the flat side of the new bulb’s plastic base facing upward, insertthe glass end of the bulb into the lamp assembly. Turn the bulb left orright

Replacing tail lamp/turn/backup lamp bulbsThe tail lamp/turn/backup lamp bulbs are located in the same portion ofthe tail lamp assembly, one just belo

To remove the brakelamp assembly:1. Remove the two screws and lampassembly from vehicle.2. Remove the bulb socket fromlamp assembly by rotating it 45d

Function Number of bulbs Trade numberHeadlamps 2 9007Park/turn/side markerlamps23157 AK (amber)Rear stop/tail /turn lamps 2 3157KBackup lamp 2 3156KHi

Vertical aim adjustment1. Park the vehicle on a level surface approximately 7.6 meters (25 feet)from a vertical wall or screen directly in front of it

3. Turn on the low beam headlampsto illuminate the wall or screen andopen the hood.4. On the wall or screen you willobserve the light pattern with adi

During winter months, it is especially important to wash the vehicle on aregular basis. Large quantities of dirt and road salt are difficult toremove

Cleaning the engineEngines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing:• Ta

To aid in side defogging/demisting in cold weather.1. Select2. Set the temperature control to full heat3. Set the fan speed to HI4. Direct the outer p

Cleaning non-painted plastic exterior partsUse vinyl cleaner for routine cleaning. Clean with a tar remover ifnecessary. Do not clean plastic parts wi

Cleaning the instrument cluster lensClean with a damp cloth, then dry with a dry cloth.Do not use household or glass cleaners as these may damage the

Inside windowsUse Ultra-Clear Spray Glass Cleaner (E4AZ-19C507–AA) for the insidewindows if they become fogged.Cleaning mirrorsDo not clean your mirro

MOTORCRAFT PART NUMBERSComponent 4.0L SOHC V6 engineAir filter element FA-1658Fuel filter FG-986BBattery BXT-65-650Oil filter FL-820SPCV valve EV-243S

Fluid Ford PartNameApplicationCapacityEngine coolant4MotorcraftPremium EngineCoolant(green-colored)or MotorcraftPremium GoldEngine Coolant(yellow-colo

4Add the coolant type originally equipped in your vehicle.5Fill to 6 mm to 14 mm (1/4 inch to 9/16 inch) below bottom of fillerplug hole.6For vehicles

ItemFord PartName orequivalentFord PartNumberFordSpecificationEngine coolant MotorcraftPremium EngineCoolant(green-colored)VC-4–A (US) orCXC-10(Canada

ItemFord PartName orequivalentFord PartNumberFordSpecificationTransfer caseFront OutputSlip ShaftPremiumLong-Life GreaseXG-1-C orXG-1-T orXG-1-KESA-M1

ENGINE DATAEngine 4.0L SOHC V6 engineCubic inches 245Required fuel 87 octaneFiring order 1-4-2-5-3-6Spark plug gap 1.3-1.4 mm (0.052-0.056 inch)Igniti

35241Capacities and specifications239

Select for air to flow throughthese vents:Selectfor air to flow throughthese vents:POWER DOWN BACK WINDOWTo operate the power down back window, the ig

IDENTIFYING YOUR VEHICLECertification labelThe National Highway Traffic SafetyAdministration Regulations requirethat a Certification label be affixedt

Ford Extended Service PlanYou can get more protection for your new car or light truck bypurchasing Ford Extended Service Plan (Ford ESP) coverage. For

If you have questions or concerns, or are unsatisfied with the service youare receiving, follow these steps:1. Contact your Sales Representative or Se

In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)In order to help

The Dispute Settlement Board may not be available in all states. FordMotor Company reserves the right to change eligibility limitations, modifyprocedu

Board membershipThe Board consists of:• three consumer representatives• a Ford or Lincoln Mercury dealership representativeConsumer candidates for Boa

Oral presentationsIf you would like to make an oral presentation, indicate YES to question6 on the application. While it is your right to make an oral

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY)In those cases where you continue to feel that the efforts by Ford andthe dealer to resolve a

If your vehicle must be serviced while you are traveling or living inCentral or South America, the Caribbean, or the Middle East, contact thenearest F

Vehicle SecurityStyled wheel protector locksVehicle security systemsComfort and convenienceCelluar phone holderCompass mirrorCompass mirror with tempe

All rear seat occupants and/or cargo must be properly restrainedand clear of the back window opening before operating thepower down rear window.Turn c

Protection and appearance equipmentAir bag anti-theft locksAutomatic headlamp systemBed matsBerber floor matsCarpet floor matsCleaners, waxes and poli

• Mobile communications systems may harm the operation of yourvehicle, particularly if they are not properly designed for automotiveuse or are not pro

California Civil Code Section 1793.22(b) presumes that the manufacturerhas had a reasonable number of attempts to conform the vehicle to itsapplicable

REPORTING SAFETY DEFECTS (U.S. ONLY)If you believe that your vehicle hasa defect that could cause a crash, orcould cause injury or death, youshould im

AAir bag supplemental restraintsystem ...112and child safety seats ...114description ...

instrument cluster lens ...231instrument panel ...230interior ...231mirrors ...

lubricationspecifications ...235, 238refill capacities ...233service points ...184starting

driving with a heavy load ...148location ...148HHazard flashers ...159Head restraints ...

high beam ...11overdrive off ...12safety belt ...10speed contro

for adults ...103–105for children ...117–118lap belt ...107warning light andc

Normal OperationIf an “up” command is selected and the ignition is switched to OFF orSTART during window travel, the window will:1. stop if it is betw

WWarning chimes ...13Warning lights (see Lights) ...8Washer fluid ...190Water, Driving throug

261

262

263

Item InformationRequired fuel Unleaded fuel only - 87 octaneFuel tank capacity 77.6L (20.5 gallons)Engine oil capacity (includes filterchange)4.7L (5.

4WD CONTROL (IF EQUIPPED)This control operates the 4WD.Refer to the Driving chapter formore information.USING YOUR AUDIO SYSTEMPremium AM/FM Stereo/Ca

Volume/power controlPress the control to turn the audiosystem on or off.Audio power can also be turned onby pressing the AM/FM selectcontrol or the ta

Tune adjust in radio mode• Press to move to the nextfrequency down the band(whether or not a listenablestation is located there). Hold thecontrol to m

BREAKING-IN YOUR VEHICLEThere are no particular guidelines for breaking-in your vehicle. Duringthe first 1 600 km (1 000 miles) of driving, vary speed

Scan functionThe scan function works in radio,tape or CD mode.Scan function in radio modePress the SCAN control to hear a brief sampling of all listen

Autoset memory presetAutoset allows you to set strong radio stations without losing youroriginal manually set preset stations. This feature is helpful

Treble adjustThe treble adjust control allows youto increase or decrease the audiosystem’s treble output.Press the TREB control then press:• to decrea

Speaker fade adjustSpeaker sound can be adjustedbetween the front and rearspeakers.Press the FADE control then press:• to shift the sound to thefront

Fast forwardThe fast forward control works intape and CD modes.• In the tape mode, tape directionwill automatically reverse whenthe end of the tape is

Compression adjustCompression adjust brings soft andloud CD passages together for amore consistent listening level.Press the COMP control to activatea

• to decrease minutes and•to increase minutes.If your vehicle has a separate clock,(other than the digital radiodisplay), the CLK control will notfunc

AM/FM Stereo In Dash Six CD Radio for Pioneer T Sound SystemVolume/power controlPress the control to turn the audiosystem on or off.Turn the control t

AM/FM selectThe AM/FM select control works inradio and CD modes.AM/FM select in radio modeThis control allows you to select AM or FM frequency bands.

Seek functionThe seek function works in radio or CD mode.Seek function in radio mode• Press to find the nextlistenable station down thefrequency band.

These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Air Bag-FrontAir Bag-

Radio station memory presetThe radio is equipped with six station memory preset controls. Thesecontrols can be used to select up to six preset AM stat

Starting autostore1. Press and momentarily hold the AM/FM control.2. AUTOSET will flash in the displayas the frequency band is scrolledthrough.3. When

Display descriptionSix circles are always lit in the digital display. These signify the six CDslots in the audio system. When a disc is loaded into a

EjectPress the EJ control to stop andeject a CD. You can choose whichCD will be ejected by pressing theEJ control and the desired presetnumber (1–6).

Fast forwardThe fast forward control works inCD modes.Press and hold the FF control untilthe desired selection is reached. Ifthe end of the disc is re

Bass adjustThe bass adjust control allows youto increase or decrease the audiosystem’s bass output.Press the BASS control. Use theSEL control to incre

Menu modeThe MENU control allows you toaccess many different featureswithin your audio system. There arethree sets of menus availabledepending upon wh

Traffic announcementsThis feature allows you to heartraffic announcements. When in thismode, traffic announcements willinterrupt radio and CD play.Whe

Radio data system (RDS) featureThis feature allows your audiosystem to receive text informationfrom RDS-equipped FM radiostations.To activate RDS:• Wh

Press the MENU control until FINDprogram type is displayed.Use the SEL control to select theprogram type. With the feature on,use the SEEK or SCAN con

Vehicle Symbol GlossaryChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Engine OilEngine CoolantEngine CoolantTemperat

Press the DSP control to access theDSP menu. Press the SEL control toenter one of the following modes:• DSP OFF• SIGNAL MODE• OCCUPANCY MODEUse the SE

Use the SEL control to manually setthe time.• Press to increasehours/minutes.• Press to decreasehours/minutes.Press the MENU control again to disengag

Adjusting the volumePress the + control to increasevolume.Press the - control to decreasevolume.From the rear seat controls, volume control can be set

Mode selectPush the MODE control to togglebetween AM, FM1, FM2, tape, CD orCD changer (if equipped).Memory preset controlPush the MEMORY controlsucces

Cleaning compact discsInspect all discs for contamination before playing. If necessary, cleandiscs only with an approved CD cleaner and wipe from the

Radio reception factorsThree factors can affect radio reception:• Distance/strength. The further an FM signal travels, the weaker it is.The listenable

POSITIONS OF THE IGNITION1. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engine is notrunning.2. LOCK, locks the

To turn speed control off• Press OFF or• Turn off the vehicle ignition.Once speed control is switched off,the previously programmed setspeed will be e

To set a higher set speed• Press and hold SET ACC. Releasethe control when the desiredvehicle speed is reached or• Press and release SET ACC tooperate

To disengage speed control• Depress the brake pedal or• Depress the clutch pedal (ifequipped).Disengaging the speed control willnot erase the previous

OFFC0123456RPMx1000ABS!ENGINEFUEL DOOR EFHHHSPEEDCONT4WDHIGH 4WDLOWO/DOFFL L CHECKGAGECHECKSUSP4X4HIGH2WD4X4LOWCHECKONRSMSETACCELCOASTOFF10M

To return to a previously set speed• Press RSM. For RSM to operate,the vehicle speed must be fasterthan 48 km/h (30 mph).Indicator lightThis light com

TILT STEERING WHEEL (IF EQUIPPED)Pull the tilt steering control towardyou to move the steering wheel upor down. Hold the control whileadjusting the wh

Push (tap) the end of the stalkbriefly for a single swipe (no wash).Push and hold for three swipes withwash. Push and hold for a longerwash (up to ten

OVERHEAD CONSOLE (IF EQUIPPED)The appearance of your vehicle’s overhead console will vary according toyour option package.Storage compartment (if equi

• Place the provided heightadaptors onto the back of theGARAGE control as needed.• Press the GARAGE control toactivate the transmitter.Moon roof (if e

Do not let children play with the moon roof. They may seriouslyhurt themselves.Electronic compass/temperature display (if equipped)Outside air tempera

Compass zone adjustment1. Determine which magnetic zoneyou are in by referring to the zonemap.2. Turn ignition to the ON position.3. Press and hold th

Compass calibration adjustmentPerform this adjustment in an openarea free from steel structures andhigh voltage lines:• Press and hold the MODE contro

POWER WINDOWSPress and hold the rocker switches to open and close windows.• Press the top portion of therocker switch to close.• Press the bottom port

Window lockThe window lock feature allows onlythe driver to operate the powerwindows.To lock out all the window controlsexcept for the driver’s press

LOADEJSHUF DSPMUTESELBALBASSFADETREBSCANTUNEPUSH ONCD1 2 3 4 5 6MENUFSEEK REW FF12 3 4 A/CMAXA/CMMA4wd control*(pg. 143)Audio system(pg. 27)Power down

Childproof door locksWhen these locks are set, the reardoors cannot be opened from theinside. The rear doors can beopened from the outside when thedoo

2. Move the control in the directionyou wish to tilt the mirror.3. Return to the center position to disable adjust function.Fold-away mirrorsPull the

CENTER CONSOLEYour vehicle may be equipped with avariety of console features. Theseinclude:• Utility compartment with compactdisc storage• Auxiliary p

AUXILIARY POWER POINTThe power point is an additional power source for electrical accessories.• With full console.• Without full console.Power outlets

Lift the cover to access the auxiliarypower point.POSITIVE RETENTION FLOOR MATPosition the floor mat so that theeyelets are over the pointed end ofthe

TAILGATE LOCKYour vehicle is equipped with atailgate lock designed to preventtheft of the tailgate.• Insert ignition key and turn to theright to engag

CARGO CAGE (IF EQUIPPED)Your vehicle may be equipped with a cargo cage designed to extend thepickup box for larger loads.To extend the cargo cage:1. L

4. Evenly push down on the cargocage and push the round knobs inon each side locking it in place.To stow the cargo cage, follow stepsone through four

Activating Cargo Cage ThiefDeterrent device:The following procedure can bedone with the cargo cage in thestowed or extended position.1. Locate the phi

To remove the cargo cage:1. Extend the cargo cage.2. Pull the round knobs on each sideof the cage to unlock it.Make sure the locking clip screwsare lo

WARNING LIGHTS AND CHIMESCheck engineYour vehicle is equipped with acomputer that monitors the engine’semission control system. Thissystem is commonly

TONNEAU COVER (IF EQUIPPED)The tonneau cover has been designed to maximize fuel economy andshould be fully installed whenever possible.The rear panel

Do not drive with front panel unlocked or folded on top of therear panel.To open the rear panel:• Open the lock cover and unlock the rear panel.• Lift

To stow the rear panel:• Before driving with the rear panel open, unlock the rear panel.• Lift the rear panel up, lay it on top of the front panel and

To remove the tonneau cover:The tonneau cover weighs 29 kg (70 lbs.) and needs to be supportedduring removal since the panels will automatically lock

To open the tonneau cover from theinside, pull the “T” shaped handleand push up on the tonneau coverpanel. The material that the handleis made of will

The remote entry features only operate with the ignition in the LOCKposition.If there is any potential remote keyless entry problem with your vehicle,

Sounding a panic alarmPress this control to activate thealarm.To deactivate the alarm, press thecontrol again or turn the ignition toON.Panic alarm wi

Replacing lost transmittersIf a remote transmitter has been lostand you would like to remove itfrom the vehicle’s memory, or youwould like to purchase

Illuminated entryThe interior lamps illuminate when the remote entry system is used tounlock the door(s) or sound the personal alarm.The system automa

The factory-set code is located:• on the owner’s wallet card in the glove compartment• marked on the computer moduleWhen pressing the controls on the

3. The fuel cap may not have been properly installed and securelytightened.These temporary malfunctions can be corrected by filling the fuel tankwith

Anti-scan featureThe keyless entry pad is disabled for1 minute after 7 unsuccessfulattempts at entering a valid keycode. The keypad will flash duringt

AutolockThe autolock feature will lock all of the vehicle doors when:• all doors are closed• ignition key is in the ON position• you shift into or thr

6. Press the power door UNLOCK control one time.7. Press the power door LOCK control to toggle the Autolock/Relockstate. You will receive a horn chirp

Key informationYour vehicle is supplied with twocoded keys. Only a coded key willstart your vehicle. Spare coded keyscan be purchased from yourdealers

If your keys are lost or stolen youwill need to do the following:• Use your spare key to start thevehicle, or• Have your vehicle towed to adealership

1. Insert the first previouslyprogrammed coded key into theignition and turn the ignition from3 (OFF) to 4 (ON) (maintainignition in 4 (ON) for at lea

FRONT SEATSAdjustable head restraintsYour vehicle’s seats may be equipped with head restraints which arevertically adjustable. The purpose of these he

Adjusting the front manual seatNever adjust the driver’s seat or seatback when the vehicle ismoving.Do not pile cargo higher than the seatbacks to red

Adjusting the front power seat (if equipped)Never adjust the driver’s seat or seatback when the vehicle ismoving.Do not pile cargo higher than the sea

Using the manual lumbar support (if equipped)Turn the lumbar support controltoward the front of vehicle to movethe lumbar support forward formore dire