Ford 2005 Expedition v.2 Manuale Utente

Introduction 4Instrument Cluster 10Warning and control lights 10Gauges 15Entertainment Systems 18AM/FM stereo cassette with CD 18AM/FM stereo with in-

WARNING LIGHTS AND CHIMESStandard instrument clusterOptional instrument clusterWarning lights and gauges can alert you to a vehicle condition that may

• Do not put objects under the front seats that will interfere with theairflow to the back seats.• Remove any snow, ice or leaves from the air intake

AUXILIARY A/C-HEATER CONTROLS (IF EQUIPPED)Your vehicle may be equipped with auxiliary climate controls. Theseallow the front or rear seat passengers

Rear auxiliary controls (if equipped):Once the front auxiliary control is set to REAR, the rear seat passengersmay use the rear auxiliary controls in

HEADLAMP CONTROLRotate the headlamp control to thefirst positionto turn on theparking lamps. Rotate to the secondpositionto turn on theheadlamps.Fogla

Daytime running lamps (DRL) (if equipped)Turns the foglamps on at full intensity output. To activate:• the ignition must be in the ON position and• th

PANEL DIMMER CONTROLUse to adjust the brightness of theinstrument panel and all applicableswitches in the vehicle duringheadlamp and parklamp operatio

5. Locate the vertical adjuster oneach headlamp, then use a 10 mmsocket/wrench to turn the adjustereither counterclockwise (to adjustdown) or clockwis

Front row map/dome lamp (if equipped)The dome lamp lights when:• any door is opened,• the instrument panel dimmerswitch is rotated up until thecourtes

Replacing exterior bulbsCheck the operation of all the bulbs frequently.Using the right bulbsReplacement bulbs are specified in the chart below. Headl

Replacing the interior bulbsCheck the operation of all bulbs frequently.Map lampsTo change the map lamp bulbs:1. Use a small screwdriver toremove the

Service engine soon: The Serviceengine soon indicator lightilluminates when the ignition is firstturned to the ON position to checkthe bulb. Solid ill

7. Once the bulb covers areremoved, the bulbs can be removedby turning them counterclockwiseand then pulling the bulbs straightout.Handle a halogen he

6. Rotate the bulb socketcounterclockwise and remove fromthe lamp assembly.7. Carefully pull the bulb out of thesocket and push in the new bulb.8. Ins

1. Remove the bulb socket from thefoglamp by turningcounterclockwise.2. Disconnect the electricalconnector from the foglamp bulb.3. Connect the new fo

Replacing license plate lamp bulbThe license plate bulbs are located in the license plate housing assemblyon the liftgate. To change the license plate

Approach lamp bulb removal (if equipped)To change the bulbs:1. Make sure that all the doors areclosed and the interior lights haveautomatically turned

MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the

Changing the wiper bladesIt is recommended that wiper blades are renewed before winter.To replace the wiper blades:1. Fold back the wiper arm andposit

TILT STEERINGPush the lever down to unlock thesteering column. While the lever isin the down position, tilt thesteering column to the desiredposition.

Slide on rod feature (ifequipped)Rotate the visor towards the sidewindow and extend it rearward foradditional sunlight coverage.Note: To stow the viso

To open the moon roof: The moonroof is equipped with a one-touchopen feature. Press and releasethecontrol. The moon roofwill open to the “comfort” pos

Anti-lock brake system: If theABS light stays illuminated orcontinues to flash, a malfunction hasbeen detected, have the systemserviced immediately. N

Power quarter rear windows (if equipped)• Without a moon roof• With a moon roofPress theportion of the VENT control to open the power rearquarter wind

Do not use the power point foroperating the cigarette lighterelement (if equipped).To prevent the fuse from beingblown, do not use the powerpoint(s) o

Not equipped with rear climatecontrolCigar/Cigarette lighter (if equipped)Do not plug optional electrical accessories into the cigarette lightersocket

One touch downAllows the driver’s window to openfully without holding the controldown. Press completely down onthe bottom part of the rocker switchand

Power side view mirrorsThe ignition can be in any position to adjust the power side view mirrors.To adjust your mirrors:1. Rotate the control clockwis

Powerfold mirrors (if equipped)Pull the switch rearwards to autofold in and rearwards again to autofold back to design position.Powerfold the side mir

Setting speed controlThe controls for using your speedcontrol are located on the steeringwheel for your convenience.1. Press the ON control and releas

Resuming a set speedPress the RES (resume) control andrelease it. This will automaticallyreturn the vehicle to the previouslyset speed. The RES contro

• Depress the brake pedal until thedesired vehicle speed is reached,press the SET + control.Turning off speed controlThere are two ways to turn off th

Audio control featuresPressto select:• AM, FM1, FM2,• CD, or• DVD (if equipped).In AM, FM1, or FM2 mode:• Press MEM to select presetstations within th

Low fuel (if equipped):Illuminates when the fuel level inthe fuel tank is at or near empty(refer to Fuel gauge in thischapter).Check fuel cap (if equi

Climate control featuresPress TMP + or - to adjusttemperature.Press+ or - to adjust fan speed.HOMELINK姞 WIRELESS CONTROL SYSTEM (IF EQUIPPED)The HomeL

Retain the original transmitter for use in other vehicles as well as forfuture programming procedures (i.e. new HomeLink威 equipped vehiclepurchase). I

5. Press and hold the just-trained HomeLink威 button and observe theindicator light. If the light is constant, programming is complete and yourdevice s

seconds (“cycle”) your hand-held transmitter until the frequencysignal has been accepted by the HomeLink威. The indicator light willflash slowly and th

For questions or comments, contact HomeLink威 at www.homelink.comor 1–800–355–3515.ELECTRONIC COMPASS/TEMPERATURE DISPLAY WITHOUTMESSAGE CENTER (IF EQU

Compass zone adjustment1. Determine which magnetic zoneyou are in for your geographiclocation by referring to the zonemap.2. Turn ignition to the ON p

4. Drive the vehicle slowly (less than 3 mph [5 km/h]) in circles untilCAL indicator turns off. As many as 5 complete circles may be required.5. The c

Compass displayThe compass reading may be affected when you drive near largebuildings, bridges, power lines and powerful broadcast antenna. Magneticor

7. To exit the zone setting mode,and to “lock in” your change, pressand release the RESET control.Perform compass calibration in an open area free fro

Average fuel economy (AFE)Select this function from the INFOmenu to display your average fueleconomy in miles/gallon or liters/100km.If you calculate

Four wheel drive low (ifequipped): Illuminates whenfour-wheel drive low is engaged. Ifthe light fails to illuminate when theignition is turned ON, con

To turn the display off or change the display from English to metric seeyour dealer.Setup menuPress this control for the followingdisplays:• System Ch

1. To disable/enable the autolampdelay feature, select this functionfrom the SETUP control for thecurrent display mode.2. Press the RESET control to s

System checkSelecting this function from theSETUP menu causes the messagecenter to cycle through each of thesystems being monitored. For eachof the mo

• They will reappear on the display ten minutes from the reset.• They will not reappear until an ignition OFF-ON cycle has beencompleted.This acts as

Warning display StatusDoor ajar Will not clear until condition iscorrectedReduced engine powerStop engine safelyCheck electronic throttlecontrol or en

LOW TIRE PRESSURE (if equipped).Displayed when one or moretires on your vehicle have low tire pressure. Refer to Inspecting andInflating Your Tires in

partially operable. If this warning stays on while the engine is running,contact your dealer for service as soon as possible. For furtherinformation,

CENTER CONSOLE (IF EQUIPPED)The center console offers several useful storage features. These include:1. Pen holder2. Tissue holder3. Large utility com

POSITIVE RETENTION FLOOR MAT (IF EQUIPPED)Position the floor mat so that theeyelet is over the pointed end of theretention post and rotate forward tol

LUGGAGE RACKYour vehicle is equipped with a roofrack. The maximum recommendedload is 200 lbs (90 kg), evenlydistributed. If it is not possible todistr

GAUGESSpeedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtempera

KEYSOne key operates all the locks and starts the vehicle. Always carry aspare key with you in case of an emergency.Your keys are programmed to your v

Childproof door locksWhen these locks are set, the reardoors cannot be opened from theinside. The rear doors can beopened from the outside when thedoo

Unlocking the doors/liftgatePress this control to unlock thedriver’s door. The interior lamps willilluminate with the ignition is in the1 (OFF/LOCK) p

Sounding a panic alarmPress this control to activate thealarm.The personal panic alarm will cyclethe horn and parking lamps on/off.To deactivate the a

Deactivating the memory seat featureTo deactivate this feature:1. Press the SET control on the driver’s door panel.2. Within 5 five seconds, press any

Note: Replacement of the battery will not cause the remote transmitterto become deprogrammed from your vehicle. The remote transmittershould operate n

Illuminated entryThe lamps illuminate when the remote entry system is used to unlockthe door(s).The system automatically turns off after 25 seconds or

KEYLESS ENTRY SYSTEM (IF EQUIPPED)With the keyless entry keypad, you can:• lock or unlock the vehicle doors without using the key,• release the liftga

Programming your own personal entry codeTo program your own code:1. Enter the factory set code (keypad will illuminate when pressed).2. Press the 1 •

To lock all doors, liftgate and liftgate window, press the 7 • 8 andthe 9 • 0 at the same time. Note: The driver’s door must be closed. Youdo not need

• With Full Message CenterRefer to Message Center in theDrivers Controls chapter on how toswitch the display from Metric toEnglish.Trip odometer: Regi

Automatic armingThe vehicle is armed immediatelyafter switching the ignition to the 1(OFF/LOCK) position.Automatic disarmingSwitching the ignition to

The correct coded key must be used for your vehicle. The use of thewrong type of coded key may lead to a “no start” condition.If an unprogrammed key i

If successful, the new coded key(s) will start the vehicle’s engine and thetheft indicator will illuminate for three seconds and then go out.If not su

SEATINGFront row adjustable head restraints (if equipped)Your vehicle’s seats are equipped with two-way adjustable headrestraints. The purpose of thes

Lift handle to move seat forward orbackward.Seat reclinerAlways drive and ride with your seatback upright and the lapbelt snug and low across the hips

Using the armrest (if equipped)Push the release control to movethe armrest up or down.Using the manual lumbar supportThe lumbar support control isloca

Adjusting the front power seat (if equipped)Never adjust the driver’s seat or seatback when the vehicle ismoving.Do not pile cargo higher than the sea

Memory seats/rearview mirrors/adjustable pedals (if equipped)This system allows automaticpositioning of the driver seat,outside rearview mirrors, anda

• There is a filter located underboth front seats.• It can be accessed from thesecond row seat. Move the frontseat all the way forward and upto ease a

To install climate controlled seat air filter:• First, position the filter in it’shousing making sure that the farforward end is all the way up inthe

Engine oil pressure gauge:Indicates engine oil pressure. Theneedle should stay in the normaloperating range (between “L” and“H”). If the needle falls

Adjusting the 2nd row outboard seat for E-Z EntryThe 2nd row outboard seats allow for easier entry and exit to and fromthe 3rd row seat.To enter the 3

3. To return the seat to a seatingposition, push down on the seatuntil the seat is latched to the floor.4. With the seat in the flat back position, li

1. Locate the handle on the side ofthe seat, lifting it to release theseatback.2. Ensure that the seat back islocked in the down position byapplying p

The rear latch hooks mustbe properly engaged withthe floor striker. Position the rearlegs of the seat over the floorstrikers and engage.2. With the se

Folding the 20% seat system (if equipped)1. Locate the release strap locatedbetween the front cushion and theseat back, and pull the strap torelease t

Before returning the seatback to its original position, make surethat cargo or any objects are not trapped underneath theseatback. After returning the

Third row seatsEnsure that no objects such as books, purses or briefcases are on thefloor in front of the third row seats or on the seat cushion befor

Folding down the third row seat to the load floorTo prevent possible damage to the seat or safety belts, ensurethat the safety belts are not buckled w

Push the top of the control buttonto return the seatback to its originalposition.The power folding seats are designed to stall within 1–10 secondsof e

• Restraint system warning light and back-up tone.• The electrical wiring for the air bags, crash sensor(s), safety beltpretensioners, front safety be

PREMIUM AM/FM STEREO/CASSETTE/SINGLE CD (IF EQUIPPED)1. EJ (Eject): Press to stop andeject a tape.2. EJ (Eject): Press to stop andeject a CD.3. BASS:

Front safety belt usage sensorsThe front safety belt usage sensors detect whether or not the driver andfront outboard passenger safety belts are faste

If any of these things happen, even intermittently, have the PersonalSafety System serviced at your dealership or by a qualified technicianimmediately

Always transport children 12 years old and under in the backseat and always properly use appropriate child restraints.Safety belts and seats can becom

movement. For example, if the driver brakes suddenly or turns a cornersharply, or the vehicle receives an impact of approximately 5 mph (8km/h) or mor

How to disengage the automatic locking modeUnbuckle the combination lap and shoulder belt and allow it to retractcompletely to disengage the automatic

Front and second row safety belt height adjustmentYour vehicle has safety belt heightadjustments for the driver, rightfront passenger and second rowou

Insert the tongue into the correctbuckle (the buckle closest to thedirection the tongue is comingfrom). To lengthen the belt, turn thetongue at a righ

Conditions of operationIf... Then...The driver safety belt is notbuckled before the ignitionswitch is turned to the ONposition...The safety belt warni

If... Then...The driver’s and frontpassenger’s safety belts arebuckled before the ignitionswitch is turned to the ONposition or less than 1-2minutes h

The following are reasons most often given for not wearing safety belts:(All statistics based on U.S. data)Reasons given... Consider...“Crashes are ra

4. BAL (Balance): Allows you toshift speaker sound between theright and left speakers. Press BALthen press SEL to shift sound to the leftor right .FAD

Do not sit on top of a buckled safety belt to avoid theBeltMinder娂 chime. Sitting on the safety belt will increase therisk of injury in an accident. T

• Step 3 must be completed within 50 seconds after the safety beltwarning light turns off.3. For the seating position being disabled, at a moderate sp

be inspected after a collision. Ford Motor Company recommends that allsafety belt assemblies in use in vehicles involved in a collision bereplaced. Ho

Always transport children 12 years old and under in the backseat and always properly use appropriate child restraints.The National Highway Traffic Saf

Children and airbagsChildren must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rear

The air bags inflate and deflaterapidly upon activation. After air bagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burn

impact sensors, the system wiring, the air bag system readiness light, theair bag back up power and the air bag ignitors).Determining if the system is

Do not attempt to service, repair, or modify the Safety Canopy娂system, its fuses, the A, B, or C pillar trim, or the headliner on avehicle containing

• Two crash sensors mounted in the front doors (one on each side ofthe vehicle).• Two crash sensors located at the c-pillar behind the rear doors (one

Several Safety Canopy娂system components get hotafter inflation. Do not touch themafter inflation.If the Safety Canopy娂 system has deployed, the Safety

Seating and Safety Restraints 163Seating 163Safety restraints 178Air bags 192Child restraints 200Tires, Wheels and Loading 214Tire Information 217Tire

In CD mode, REW control reverses the CD within the current track.FF (Fast Forward): Works in tapeand CD modes.In the tape mode, tape directionautomati

SAFETY RESTRAINTS FOR CHILDRENSee the following sections for directions on how to properly use safetyrestraints for children. Also see Air bag supplem

Child booster seatsChildren outgrow a typical convertible or toddler seat when they weigh40 lb. (18 kg) and are around 4 years of age. Although the la

Types of booster seatsThere are two types of belt-positioning booster seats:• Those that are backless.If your backless booster seat has aremovable shi

Follow all instructions provided by the manufacturer of thebooster seat.Never put the shoulder belt under a child’s arm or behind theback because it e

• Put the safety belt in the automatic locking mode. Refer to Automaticlocking mode section in this chapter.• The second row center seat can be moved

1. Position the child safety seat in aseat with a combination lap andshoulder belt.2. Pull down on the shoulder beltand then grasp the shoulder beltan

4. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) for that seating position untilyou hear

8. Allow the safety belt to retract toremove any slack in the belt.9. Before placing the child in theseat, forcibly move the seat forwardand back to m

6. Before placing the child into the child seat, forcibly move the childseat from side to side and forward to make sure that the seat is heldsecurely.

Second row seating positions1. Position the child safety seat on the seat cushion.2. Locate the tether anchor at the bottom back of the seat.• outboar

11. AUTOSET: Press to set first sixstrong stations into AM, FM1 orFM2 memory buttons; press again toreturn to the original presetstations. If there ar

5. Rotate the tether strap, and clipthe tether strap to the anchor onthe seat frame.6. Rotate the tether strap clip.7. Tighten the child safety seat t

• You may need to pull back thetop of the hinged panel along thebottom of the seat back to accessthe tether anchor.4. Clip the tether strap through th

Your vehicle has LATCH anchors for child seat installation at the seatingpositions marked with the child seat symbol:Never attach two LATCH child safe

Attach LATCH lower attachments of the child seat only to theanchors shown.If you install a child seat with rigid LATCH attachments, do not tightenthe

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERSUtility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare e

Power is supplied to all four wheelsthrough a transfer case or powertransfer unit. 4WD vehicles allowyou to select different drive modesas necessary.

• Narrower — to provide greatermaneuverability in tight spaces,particularly in off-road use.As a result of the above dimensionaldifferences, SUV’s and

and one-half (1 1/2) times as well on the government course as a tiregraded 100. The relative performance of tires depends upon the actualconditions o

• Tire Identification Number (TIN): A number on the sidewall ofeach tire providing information about the tire brand andmanufacturing plant, tire size

Every day before you drive, checkyour tires. If one looks lower thanthe others, use a tire gauge to checkpressure of all tires and adjust ifrequired.A

To engage the speed sensitive volume feature, press and hold the volumecontrol for five seconds (with the radio on). Press SEL toincrease/decrease vol

Under-inflation is the most common cause of tire failures andmay result in severe tire cracking, tread separation or ⬙blowout⬙,with unexpected loss of

when you get to the pump. It is normal for tires to heat up and the airpressure inside to go up as you drive. Never “bleed” or reduce airpressure when

The installation of replacement tires with steel cord body plies in the tiresidewall may cause malfunction of the Tire Pressure Monitoring System(TPMS

Your vehicle may be equipped with a dissimilar spare tire/wheel. Adissimilar spare tire/wheel is defined as a spare tire and/or wheel that isdifferent

If your vehicle is equipped with TPMS, have a flat tire serviced by adealer or qualified technician in order to prevent damage to the TPMSsensor, refe

Removing the spare tire1. Fold the rear seat down. Refer toRear seats in the Seating andsafety restraints chapter.2. Remove the jack handle andwinch e

1. Park on a level surface, activatehazard flashers and set the parkingbrake.2. Place gearshift lever in P (Park),turn engine OFF and block thediagona

6. Lift the vehicle so the tire is no further than 1 inch (2.5 cm) off theground when installing the spare tire.When one of the rear wheels is off the

To lessen the risk ofpersonal injury, do not putany part of your body under thevehicle while changing a tire. Donot start the engine when yourvehicle

2. Slide the wheel partially underthe vehicle and install the retainerthrough the wheel center. Afterdoing so, pull on the cable to alignthe component

PREMIUM IN-DASH SIX CD SOUND SYSTEM (IF EQUIPPED)AUDIOPHILE SATELLITE READY AM/FM STEREO IN-DASH SIX CDRADIO (IF EQUIPPED)1. Seek: Press and releaseSE

INFORMATION CONTAINED ON THE TIRE SIDEWALLFederal law requires tire manufacturers to place standardizedinformation on the sidewall of all tires. This

7. H: Indicates the tire’s speed rating. The speed rating denotes thespeed at which a tire is designed to be driven for extended periods oftime under

10. Tire Ply Composition and Material Used: Indicates the number ofplies or the number of layers of rubber-coated fabric in the tire tread andsidewall

Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;

Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8

TIRE CAREImproper or inadequate vehicle maintenance can also cause tires to wearabnormally. Here are some of the important maintenance items:Tire wear

Safety practicesDriving habits have a great deal to do with your tire mileage and safety.• Observe posted speed limits• Avoid fast starts, stops and t

The tires should also be balanced periodically. An unbalanced tire andwheel assembly may result in irregular tire wear.Tire rotationRotating your tire

• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/ All Wheel Drive (AWD)vehicles (front tires at top ofdiagram)Sometimes irregular tire wear can

information placard (label). Driving on a significantly under-inflated tirecauses the tire to overheat and can eventually lead to tire failure.Under-i

2. REW (Rewind): In CD mode,press to reverse within the currenttrack.Fast forward: In CD mode, press until desired selection is reached.TEXT: TEXT is

parked. The Low Tire Warning Lamp will turn ON if the tire pressure is25% below the pressure listed on the tire label (approximately 6 to 9 psibelow t

Low Tire WarningLightCustomer Action RequiredSolid Warning Light 1. Check your tire pressure to ensure they areproperly inflated, refer to Inspecting

therefore it may take up to a minute for the light to turn off after youhave filled your tires to the recommended tire pressure.• If your vehicle has

interference, and (2) This device must accept any interference received,including interference that may cause undesired operation.The Tire Pressure Mo

capability, with or without a trailer. Properly loading your vehicle willprovide maximum return of vehicle design performance. Before loadingyour vehi

Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load

GAW (Gross Axle Weight) – is the total weight placed on each axle(front and rear) – including vehicle curb weight and all payload.GAWR (Gross Axle Wei

GVWR (Gross Vehicle WeightRating) – is the maximumallowable weight of the fully loadedvehicle (including all options,equipment, passengers and cargo).

mandatory options, no cargo (internal or external), a tongue load of10–15% (conventional trailer) or king pin weight of 15–25% (fifth wheeltrailer), a

6. If your vehicle will be towing a trailer, load from your trailer will betransferred to your vehicle. Consult this manual to determine how thisreduc

Treble: Press TREB; then pressSEL/ to decrease/increasethe treble output.7. Select: Use with Bass, Treble,Balance and Fade controls to adjustlevels an

Special loading instructions for owners of pickup trucks andutility-type vehiclesFor important information regarding safe operation of this typeof veh

Trailer towing (standard equipment):Your vehicle is equipped with a integrated trailer hitch and a Class I(4-pin) trailer electrical connector. The 4-

EngineRear axleratioMaximum GCWR -kg (lb.)Trailer weightrange (0 -maximum) kg (lb.)4x45.4L withstandardtrailer towpackageAll 5397 (11900) 0–2721 (0–60

• Weight distributing - requires an aftermarket weight distributingsystem which includes draw bar, hitch ball, spring bars and snap-upbrackets. The ve

4. Attach the trailer to the vehicle and adjust the hitch equalizers so thatthe front bumper height is within a1⁄2” (13 mm) of the reference point.Aft

• Consult your local motor vehicle speed regulations for towing a trailer.• To eliminate excessive shifting, use a lower gear. This will also assistin

Exceeding these limits may allow water to enter vehicle components:• causing internal damage to the components.• affecting driveability, emissions and

STARTINGPositions of the ignition1. OFF/LOCK, locks the steeringwheel, automatic transmissiongearshift lever and allows keyremoval.2. ACCESSORY, allow

If you smell exhaust fumes inside your vehicle, have your dealerinspect your vehicle immediately. Do not drive if you smellexhaust fumes.Important saf

5. Turn the key to 3 (ON) withoutturning the key to 4 (START).Make sure the corresponding lights illuminate or illuminate briefly. If alight fails to

Compression: Brings soft and loud CD passages together for a moreconsistent listening level when in CD model. Press MENU untilcompression status is di

3. After idling for a few seconds, apply the brake, shift into gear anddrive.Note: If the engine does not start within five seconds on the first try,t

Important ventilating informationIf the engine is idling while the vehicle is stopped for a long period oftime, open the windows at least one inch (2.

The ABS operates by detecting the onset of wheel lockup during brakeapplications and compensates for this tendency. The wheels areprevented from locki

Parking brakeApply the parking brake wheneverthe vehicle is parked. To set theparking brake, press the parkingbrake pedal down until the pedalstops.Th

Pull the release lever to release thebrake. Driving with the parkingbrake on will cause the brakes towear out quickly and reduce fueleconomy.STEERINGY

easier entry. When a door or the liftgate is opened, the systemmemorizes and maintains that height until either all doors are closed orthe vehicle’s s

Press the bottom portion of theswitch to turn off the airsuspension.LIMITED-SLIP AXLE (IF EQUIPPED)This axle provides added traction on slippery surfa

Vehicles with a higher center of gravity such as utility andfour-wheel drive vehicles handle differently than vehicles with alower center of gravity.

down, the system will again function normally. Anti-lock braking is notaffected by this condition and will function normally during thecool-down perio

The AdvanceTrac威 with RSC buttonallows the driver to control theavailability of the AdvanceTrac威with RSC system. The RSC systemstatus is indicated by

Speed sensitive volume: Radio volume changes automatically andslightly with vehicle speed to compensate for road and wind noise.Recommended level is 1

Do not alter or modify your vehicle’s suspension or steering; theresulting changes to the vehicle’s handling can adversely affectthe AdvanceTrac威 with

3. Locate the round access plug onthe underside of the steeringcolumn cover.4. Remove the access plug using a flat-head screwdriver, then insert yourf

slightly delayed. Once the engine coolant temperature reaches 160°F(71°C) the normal shift strategy will resume. This is normal operationand will not

D (Drive) with OverdriveThe normal driving position for thebest fuel economy. Transmissionoperates in gears one through four.D (Drive) without Overdri

1 (First)Use 1 (Low) to provide maximumengine braking on steepdowngrades. Upshifts can be madeby shifting to 2 (Second) or to D (Drive). Selecting 1 (

To help avoid personal injury, please read and understand thelimitations of the reverse sensing system as contained in thissection. Reverse sensing is

The RSS detects obstacles up to sixfeet (two meters) from the rearbumper with a decreased coveragearea at the outer corners of thebumper, (refer to th

CONTROL TRAC FOUR-WHEEL DRIVE (4X4) OPERATION(IF EQUIPPED)For important information regarding safe operation of this typeof vehicle, see Preparing to

Positions of the Control Trac systemThe Control Trac system functionsin four modes:• 2H (2WD HIGH) delivers powerto the rear wheels only. This isappro

Utility and four-wheel drive vehicles are not designed forcornering at speeds as high as passenger cars any more thanlow-slung sports cars are designe

Press to scroll through a list of categories, (i.e., Pop, Rock, Country, HipHop, R&B, Dance, Jazz/Standards, Classical, Variety, News, Sports andE

Shifting from 2H, A4WD or 4H to 4L1. Bring the vehicle to a stop andkeep the brake pedal depressed.2. Place the gearshift in N (Neutral).3. Move the c

How your vehicle differs from other vehiclesTruck and utility vehicles can differ from some other vehicles. Yourvehicle may be higher to allow it to t

Vehicles with a higher center of gravity such as utility andfour-wheel drive vehicles handle differently than vehicles with alower center of gravity.

called for. Avoid abrupt steering, acceleration or braking which couldresult in an increased risk of loss of vehicle control, vehicle rolloverand/or p

momentary clunk and ratcheting sounds. This is the front drivetraincoming up to speed and engaging the front wheels, and is not cause forconcern.SandW

slowly and avoid spinning your wheels. If the vehicle does slide, steer inthe direction of the slide until you regain control of the vehicle.If the tr

Descend a hill in the same gear youwould use to climb up the hill toavoid excessive brake applicationand brake overheating. Do notdescend in neutral;

Company strongly recommends that you do not make modifications suchas adding or removing parts (such as lift kits or stabilizer bars) or byusing repla

GETTING ROADSIDE ASSISTANCETo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program

U.S. Ford or Mercury vehicle customers who require roadside assistance,call 1–800–241–3673; Lincoln vehicle customers call 1–800–521–4140.Canadian cus

TREB (Treble): Allows you toincrease or decrease the audiosystem’s treble output. Press TREBthen press TEXT/SEL todecreaseor increase the treble level

The fuel pump shut-off switch is located in the left rear quarter trimpanel, near the liftgate. The switch is located behind an access panel.The fuel

FUSES AND RELAYSFusesIf electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinth

Passenger compartment fuse panel / power distribution boxThe fuse panel is located under the right-hand side of the instrumentpanel.To remove the trim

The fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description1 7.5A* Run/Accessory - Front wipermotor, In

Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description5 7.5A* Powertrain Control Module (PCM)(KA power), Speed controldeactivatio

Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description12 15A* Fuel pump relay, Fuel pumpshut-off switch, Fuel pump drivermodule,

Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description20 30A* BSM (door locks, liftgate glassrelease relay), Liftgate glassreleas

Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description29 30A* Trailer tow electric brakecontroller, Trailer tow 7–wireconnector (

Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description41 20A* Cigarette lighter, OBD IIdiagnostic connector42 10A* Trailer tow le

Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description115 30A** Transfer case shift motor, 4x4relays116 40A** Front blower motor

Maintenance and Specifications 324Engine compartment 326Engine oil 327Battery 331Engine Coolant 333Fuel information 339Air filter(s) 353Part numbers 3

9. REW (Rewind): Worksintapeand CD modes.In tape mode, radio play continuesuntil rewind is stopped (by pressing REW again) or the beginning of thetape

Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel DescriptionR203 PCM relay Fuse 32, Fuse 34, PCM solenoidsand sensorsR301 Trailer towba

Preparing your vehicleWhen the battery is disconnected or a new battery is installed, thetransmission must relearn its shift strategy. As a result, th

2. Connect the other end of the positive (+) cable to the positive (+)terminal of the assisting battery.3. Connect the negative (-) cable to the negat

4. Make the final connection of the negative (-) cable to the jumpstarting stud located in the rear of the engine compartment, near thebattery. Do not

Removing the jumper cablesRemove the jumper cables in the reverse order that they wereconnected.1. Remove the jumper cable from the ground metal surfa

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of

WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y

If the vehicle is towed by other means or incorrectly, vehicledamage may occur.With a disabled vehicle (without access to wheel dollies, car haulingtr

GETTING THE SERVICES YOU NEEDAt homeYou must take your Ford vehicle to an authorized Ford dealer forwarranty repairs. While any Ford dealership handli

In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf yo

Press TEXT/SEL to increase /decrease volume compensationlevels. The selected level will appear in the display.• Compression: In CD/MP3 modes, select t

In the United States, a warranty dispute must be submitted to theDispute Settlement Board before taking action under the Magnuson-MossWarranty Act, or

• available free to owners and lessees of qualifying Ford Motor Companyvehicles.The Dispute Settlement Board may not be available in all states. FordM

• A Ford or Lincoln Mercury dealership representativeConsumer candidates for Board membership are recruited and trained byan independent consulting fi

before the Board, this is not a requirement and the Board will decide thecase whether or not an oral presentation is made. An oral presentationmay be

The CAMVAP program is a straight-forward and relatively speedyalternative to resolve a disagreement when all other efforts to produce asettlement have

GETTING ASSISTANCE OUTSIDE THE U.S. AND CANADABefore exporting your vehicle to a foreign country, contact theappropriate foreign embassy or consulate.

ORDERING ADDITIONAL OWNER’S LITERATURETo order the publications in this portfolio, contact Helm, Incorporated at:HELM, INCORPORATEDP.O. Box 07150Detro

WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is

roof racks, bumper step surfaces, mirror housings or the windshieldcowl area. The paint sealant will “gray” or stain the parts over time.PAINT CHIPSYo

• Cover the highlighted areas to prevent water damage when cleaningthe engine.• 5.4L 3V engine• Never wash or rinse the engine while it is running; wa

“nominal” listening level when the ignition switch is turned back on.Audio power can also be turned on by pressing BAND or the TAPE orCD controls.17.

Do not use sharp objects, such as a razor blade, to clean theinside of the rear window or to remove decals, as it may causedamage to the rear window d

LEATHER SEATS(IF EQUIPPED, EXCEPT FOR THE KING RANCH EXPEDITION)Your leather seating surfaces have a clear, protective coating over theleather.For Kin

• Do not use household cleaning products, alcohol solutions, solvents orcleaners intended for rubber, vinyl or plastics.ScratchesIn order to lessen th

Motorcraft Custom Bright Metal Cleaner (ZC-15)Motorcraft Custom Clear Coat Polish (ZC–8–A)Motorcraft Custom Vinyl Protectant (U.S. only) (ZC-40-A)Moto

SERVICE RECOMMENDATIONSTo help you service your vehicle:• We highlight do-it-yourself items in the engine compartment for easylocation.• We provide sc

OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel.2. Go to the front of the vehicle a

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT5.4L 3V– V8 engines1. Battery2. Automatic transmission fluid dipstick3. Air filter assembly4. Engine o

WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer

4. Open the hood. Protect yourself from engine heat.5. Locate and carefully remove theengine oil level indicator (dipstick).6. Wipe the indicator clea

• If required, add engine oil to theengine. Refer to Adding engineoil in this chapter.• Do not overfill the enginewith oil. Oil levels above thismark

AUDIOPHILE/PREMIUM SATELLITE COMPATIBLE AM/FM STEREOIN-DASH SIX CD/MP3 RADIO (IF EQUIPPED)1. SEEK: Press and releaseSEEK/ for previous/nextstrong stat

Engine oil and filter recommendationsLook for this certificationtrademark.Use SAE 5W-20 engine oil.Only use oils “Certified For Gasoline Engines” by t

BATTERYYour vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice.How

Batteries normally produce explosive gases which can causepersonal injury. Therefore, do not allow flames, sparks or lightedsubstances to come near th

battery. When the battery is disconnected or a new battery is installed,the engine must relearn its idle and fuel trim strategy for optimumdriveabilit

concentration testing is possible with a hydrometer or antifreeze tester(such as the Rotunda Battery and Antifreeze Tester, 014–R1060). Thelevel of co

low or empty, add engine coolant to the reservoir. Refer to Addingengine coolant in this chapter.Note: Automotive fluids are not interchangeable; do n

• Do not use alcohol, methanol, brine or any engine coolantsmixed with alcohol or methanol antifreeze (coolant). Alcoholand other liquids can cause en

necessary, add enough 50/50 concentration of engine coolant anddistilled water to bring the liquid level to the proper level.If you have to add more t

• Decreased engine coolant concentrations below 40% willdecrease the corrosion protection characteristics of the enginecoolant and may cause engine da

Once the engine temperature cools, the engine can be re-started. Takeyour vehicle to a service facility as soon as possible to minimize enginedamage.W

3. AUX: Press to toggle between thecurrent playing media and DVD (ifequipped).4. MUTE: Press to MUTE playingmedia; press again to return toplaying med

Automotive fuels can cause serious injury or death if misused ormishandled.Gasoline may contain benzene, which is a cancer-causing agent.Observe the f

When refueling always shut the engine off and never allowsparks or open flames near the filler neck. Never smoke whilerefueling. Fuel vapor is extreme

2. Carefully turn the filler cap counterclockwise 1/4 turn until it stops.3. Pull to remove the cap from the fuel filler pipe.4. To install the cap, a

Repairs to correct the effects of using a fuel for which your vehicle wasnot designed may not be covered by your warranty.Octane recommendationsYour v

• Your Service engine soon indicator may come on. For moreinformation on the Service engine soon indicator, refer to theInstrument Cluster chapter.Fue

• Use the same filling rate setting (low — medium — high) each timethe tank is filled.• Allow no more than 2 automatic click-offs when filling.• Alway

• Idling for long periods of time (greater than one minute) may wastefuel.• Anticipate stopping; slowing down may eliminate the need to stop.• Sudden

• Using fuel blended with alcohol may lower fuel economy.• Fuel economy may decrease with lower temperatures during the first8–10 miles (12–16 km) of

emission control, such non-Ford parts should be equivalent to genuineFord Motor Company parts in performance and durability.Do not park, idle, or driv

These temporary malfunctions can be corrected by filling the fuel tankwith good quality fuel and/or properly tightening the fuel cap. After threedrivi

Traffic (if equipped): Allows you to hear traffic broadcasts. With thefeature ON, press SEEK or SCAN to find a station broadcasting a trafficreport (i

1. Start the engine and let it rununtil it reaches normal operatingtemperature (the engine coolanttemperature gauge indicator will benear the center o

temperature (approximately 20 miles [30 km]). If your vehicle has beenoperated for an extended period at high speeds, in city traffic during hotweathe

The transmission fluid should be inthis range if at ambient temperature(50°F-95°F [10°C-35°C]).High fluid levelFluid levels above the safe rangemay re

When changing the air filter element, use only the Motorcraft air filterelement listed. Refer to Motorcraft part numbers in this chapter.Note: Do not

MOTORCRAFT PART NUMBERSComponent 5.4L 3V V8 engineAir filter element FA-1754Battery BXT-65-650Fuel filter FG-986BOil filter FL-820-SPCV valve1Spark pl

REFILL CAPACITIESFluid Ford PartNameApplication CapacityBrake fluid Motorcraft HighPerformanceDOT 3 MotorVehicle BrakeFluidAll Fill to line onreservoi

Fluid Ford PartNameApplication CapacityEngine coolant3MotorcraftPremium GoldEngine Coolant(yellow-colored)5.4L BaseRadiator withoutaux rear heat19.4 q

Some transmission fluids may be labeled as dual usage, such asMERCON威 and MERCON威 V. These dual usage fluids are not to be usedin an automatic transmi

LUBRICANT SPECIFICATIONSItemFord partnameFord partnumberFordspecificationHinges, latches,striker platesand rotors, seattracks, fuel fillerdoor hinge a

ItemFord partnameFord partnumberFordspecification4x4 front wheelbearings, 4x4spindle needlebearings, spindlethrust bearings& front driveaxle u-joi

10. REPEAT: Press to repeat thecurrent CD/MP3 track.11. SHUFFLE: Press play theCD/MP3 tracks on the current discin random order.12. FOLDER: Press to a

in an automatic transmission that requires use of the MERCON威 typefluid. However, these dual usage fluids may be used in transmissions thatrequire the

Vehicle dimensions 4x2 – inches (mm) 4x4 – inches (mm)(4) Wheelbase 119.0 (3023) 119 (3023)(5) Track - Front 67.0 (1701) 67.0 (1701)(5) Track - Rear 6

IDENTIFYING YOUR VEHICLECertification labelThe National Highway Traffic SafetyAdministration Regulations requirethat a Certification label be affixedt

7. Assembly plant8. Production sequence numberEngine numberThe engine number (the last eight numbers of the vehicle identificationnumber) is stamped o

GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local authorized Ford

Interior styleElectrochromatic compass/temperature interior mirrorsFloor matsScuff platesLifestyleBike racksCargo organization and managementSmoker’s

• Mobile communications systems may harm the operation of yourvehicle, particularly if they are not properly designed for automotiveuse.• To avoid int

AABS (see Brakes) ...261Accessory delay ...123Air bag supplemental restraintsystem ...

washing ...317waxing ...317wheels ...318wiper bl

change oil soon warning,message center ...327checking and adding ...327dipstick ...327

20. Load: Press to load a CD. Pressand hold to load up to six discs.21. CD: Press to enter CD mode.CD units are designed to play commercially pressed

Inspection/maintenance (I/M)testing ...349Instrument panelcleaning ...320cluster

PPanic alarm feature, remoteentry system ...153Parking brake ...263Parts (see Motorcraft parts) ..

Steering wheelcontrols ...128tilting ...117TTire Pressure MonitoringSystem (TPMS)

373

374

375

376

REAR SEAT RADIO CONTROLS (IF EQUIPPED)If your vehicle is equipped with afront row console, then it is alsoequipped with rear seat radiocontrols.If you

To activate Dual Play mode (rearseat passengers listen to a differentplaying media than the front seatpassengers):• Press the speaker/headphonecontrol

CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth

Turning the rear speakers on and offPress the headphone/speakercontrol to turn the rear speakers on(Single Play mode) or off (Dual Playmode).Using hea

Memory preset controlPush the MEMORY/MEM controlsuccessively to allow rear seatpassengers to scroll through the 6memory presets in AM, FM1 orFM2.Push

RADIO FREQUENCIESAM and FM frequencies are established by the Federal CommunicationsCommission (FCC) and the Canadian Radio and TelecommunicationsComm

Don’t:• Expose discs to direct sunlight or heat sources for extended periodsof time.• Insert more than one disc into each slot of the CD changer magaz

DVD player controls1. MAIN control• NEXT — Press to access the next track on the CD, the next chapteron the DVD, or to go up in cursor mode.• PREV — P

7. Auxiliary jacksInsert lines for standard video game players.8. STOP/EJECT controlPress once to stop DVD play. Press again to eject the DVD.9. DISPL

• Press the FWD control to movethe cursor right one positionNext/Previous controlThe NEXT (up) and PREV (down)controls allow you to access thenext or

FWD or REV control for slow motion playback. Three different speedsare available depending on how long the control is held. Press thecontrol once for

Remote control1. REWIND controlPress to reverse the direction of the DVD movie.2. FAST FORWARD controlPress to advance the direction of the DVD movie.

8. VOLUME controlPress to increase (+) or decrease (-) volume level.Battery replacementBatteries are supplied with theremote control unit. Since allba

Warning symbols on your vehicleWhen you see this symbol, it isimperative that you consult therelevant section of this guide beforetouching or attempti

To install the batteries, lightly pressdown on the top of the left earpieceand slide the cover off.When replacing the batteries, usetwo new batteries

Liquid Crystal Display (LCD) flip-down screenThe screen rotates down to view and into the housing to store when notin use. Be sure the screen is latch

Rear Seat Entertainment DVD System protection circuitsHigh temperature sensor circuit• Excessively high temperatures may cause damage to the DVD playe

Inserting a CD/DVDPartially insert the CD/DVD into the slot and the system will fully pull inthe disc. Inserting the disc too far could cause the disc

On-screen indicatorsEach time a control is pressed, the operational status of the DVD playeris shown on the screen. The following are some possible in

Do not expose the liquid crystal display (LCD) flip-down screento direct sunlight or intensive ultraviolet rays for extensiveperiods of time. Ultravio

• extremely hot or cold temperatures.• direct sunlight.• high humidity.• a dusty environment.• locations where strong magnetic fields are generated.Te

VEHICLE NAVIGATION RADIO (VNR IF EQUIPPED)Your vehicle may be equipped with a Vehicle Navigation Radio (VNR)which allows you to listen to the radio, p

• The navigation system is not a substitute for your personal judgement.• Route suggestions should not supersede local traffic regulations orsafe driv

System overview1. HOME: When the home locationis empty, pressing and holding thiskey will store the vehicle’s currentlocation as home. Pressing the ho

Service Data RecordingService data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehicle. This pote

4. Cursor control: Use this controlwhen viewing a menu in thenavigation system. Press the controlup or down, left or right to highlightan item in the

11. On/volume: Press the ONcontrol to turn on the VNR system.Press again to turn the system off.Turn the control to adjust the audiovolume levels. To

2. Press the AM/FM control to selectthe desired frequency band.3. Press the SEEK control to locatea station.To play a CD in the VNR:1. Ensure that the

2. Press the NAV control to enterinto Navigation mode.3. To enter a destination, ensurethat the vehicle is in the PARK position.4. To navigate to home

Automatic volume control (AVC)With this feature, radio volume changes automatically with vehicle speedto compensate for road and wind noise. To engage

AM/FM select in CD modePress to stop CD play and begin radio play.Radio reception factors:• Distance/strength. The further an FM signal travels, the w

Adjusting the levels1. Press the MENU control.2. Select the AUDIO OPTIONS softkey.3. Select BASS, TREB, BAL orFADE.The bass adjust allows you toincrea

You can then select from thefollowing signal modes:• NEWS — ”voice-only” type ofsound with a limited audio band• JAZZ CLUB — jazz club withclearly ref

Seek in CD or CD DJ mode• Pressto seek to the previous track of the current disc. If aselection has been playing for three seconds or more and youpres

Starting autoset memory preset1. Select a frequency band using the AM/FM select controls.2. Press the AUTO control.3. When the first six strong statio

Special instructionsFor your added safety, your vehicle is fitted with sophisticated electroniccontrols.Please read the section Supplemental restraint

Scan functionPress the soft key next to SCAN fora brief sampling of all listenablestations on the selected frequency.Press again to disable scan andre

CompressionThe compression feature will boostquieter music and lower loudermusic to minimize the need forvolume adjustments.When in CD or CD DJ mode,

(STOP) / AUX — If a DVD movie is playing, press to stop. If a movieis not playing, press to activate AUX mode.CD DJYour vehicle is equipped with a CD

Press to eject the magazine.1. Pull the lever to remove a CDtray from the magazine.2. Insert one disc into each CD trayof the magazine (up to 6 discs)

4. Insert the CD magazine into theCD DJ.5. Slide the door to the left to close.Use only compact discs containingthis mark.The magazine does not need t

CD DJ information screenThe CD DJ screen will displayvarious information such as:• Track selected• Elapsed time• Selected disc• Volume level• On-scree

Scan featureWhen in CD DJ mode, press SCANfor a brief sampling of all tracks onthe current CD. Press again todisengage the feature and listen tothe se

will disable rear seat control (headphone/speaker icon on display willappear with a red slash through it).When RSC is active, pressing presets 2 and 4

Please drive safelyThis screen may appear on yourVNR display. Press the soft key nextto the display to select the desiredlanguage. Press the control n

Limited GPS receptionSystem performance may be adversely affected if GPS reception isinterrupted or interference occurs over a distance of several mil

These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Air Bag-FrontAir Bag-

Map display informationWhen using the navigation system,the map display screen will appearto guide you to your location. Onthe screen, you are able to

Address/IntersectionUse the soft keys to selectAddress/Intersection from theDestination Entry menu. The nexttwo options available are:• Town/City Name

• Within a Town/City – Lists entries for a specific city in alphabeticalorder.Certain categories may not be available in some areas and POIs may notal

• To move back to previously selected characters, press DELETE.List – Your VNR system shows a list of town/cities, streets or points ofinterest and a

This screen will appear for a fewseconds while the navigation systemis calculating your route.Please proceedOnce the route is calculated, ’PleaseProce

Guide displayOnce your vehicle is moving alongthe highlighted route, the Guidedisplay screen will automaticallyappear. This screen shows your nextturn

ArrivalWhen you approach yourdestination, the destination indicatorwill appear on the map displayscreen as a circular icon. When youarrive, the name a

6. Press the EDIT soft key to editthe current entry.• Use the cursor control to select aletter.• Push the control to add a letterto the name. If you m

Detours, route interruptions and changesIf need be, your navigation systemcan easily and quickly find the mostefficient detour around roadconstruction

• Resume route - The navigationsystem displays the Select RouteCriteria screen. Refer toSelecting Route Criteria earlierin this chapter.• Cancel route

Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Eng

• UNITS — Press to select from miles or kilometers. When Km areselected, it will affect the map and the fuel economy screen.Display optionsUse this fe

2. Press the ADJUST control toselect the hours or minutes to set.3. Use the cursor control to increaseor decrease the hours or minutes.4. Press DONE t

• Always store the map CDs in their protective cases when not in use.Map coverageThe following map data CDs are available for the navigation system:•

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)1. Temperature selection:Controls the temperature of theairflow in the vehicle.2. Air flow sele

• Under normal weather conditions, do not leave the air flow selector inMAX A/C or OFF when the vehicle is parked. This allows the vehicleto “breathe”

1. A/C control: Uses outside air tocool the vehicle. Press to turn on/offin all modes exceptor .2. Recirculation control: Used tomanually enable or di

12. AUTO: Press AUTO and thenselect the desired temperature. Thesystem will automatically determinefan speed, airflow location and outside or recircul

DUAL AUTOMATIC TEMPERATURE CONTROL (DATC) SYSTEMWITH HEATED AND COOLED SEATS (IF EQUIPPED)1. A/C control: Press toengage/disengage the airconditioning

5.R(Rear defroster): Press to defrost the rear window. Refer to theRear window defroster section in this chapter for more information.6. Passenger coo

be illuminated). Press a second time to select medium heat (two lights).Press a third time to select low heat (one light). Press a fourth time todisen