Ford 2011 Escape Hybrid v.2 Manuale Utente

Introduction 4Instrument Cluster 18Warning lights and chimes 18Gauges 23Message center 25Entertainment Systems 34AM/FM stereo with CD/MP3 34Auxiliary

Question AnswerAfter I start my car in themorning, why does it take along time before the engineshuts down?There are several reasons the enginestays o

Condition Potential CausesCannot clear MyKey™ • Key in the ignition is a MyKey™• No MyKeys™ are programmed to thevehicle. Refer to Create a MyKey™ sec

POWER DOOR LOCKS• Press thecontrol to unlock alldoors.• Press thecontrol to lock alldoors.Door key unlocking/lockingUnlocking the doorsTurn the key in

Note: The autolock feature can be activated/deactivated independentlyof the autounlock feature.Before following the activation or deactivation procedu

Message center procedureFor information on activating/deactivating the autolock feature using thevehicle’s message center, refer to Message center inf

1. Place the key in the ignition andturn the ignition to the on position.2. Press the power door unlockcontrol on the door panel threetimes.3. Turn th

CHILDPROOF DOOR LOCKSWhen these locks are set, the reardoors cannot be opened from theinside. The rear doors can beopened from the outside when thechi

The IKT allows you to:• remotely unlock the vehicledoors.• remotely lock all the vehicledoors.• remotely open the power liftgateglass.• activate the p

4 seconds. The turn signal will flash twice to indicate that the vehicle hasswitched to one step unlocking. Repeat the procedure to switch back totwo

To replace the battery:1. Twist a thin coin in the slot of theIKT near the key ring in order toremove the battery cover.Note: Do not wipe off any grea

The illuminated entry system will turn off the lights if:• the ignition is turned to the on position, or• the integrated keyhead transmitter lock cont

Question AnswerWhat is the fan noise I hearfrom the rear of my hybrid?The fan noise comes from two fanslocated inside the high voltage battery.These f

2. Within five seconds press the 1 • 2 on the keypad. The doors will lockand then unlock to confirm that the system is in programming mode.3. Enter yo

To unlock all doors and liftgate, press the 3 • 4 control within fiveseconds of entering the factory set 5-digit code or your personal code.To lock al

Anti-theft indicatorThe anti-theft indicator is located in the instrument panel cluster.• When the ignition is in the offposition, the indicator will

keyless entry transmitter. A maximum of eight coded keys can beprogrammed to your vehicle; only four of these eight keys can be IKTswith remote entry

4. After three seconds but within 10 seconds of turning the ignition tothe 1 (off) position, insert the second previously coded key into theignition.5

FRONT SEATSWARNING: Reclining the seatback can cause an occupant toslide under the seat’s safety belt, resulting in severe personalinjuries in the eve

To adjust the head restraint, do the following:1. Adjust the seatback to an upright driving/riding position.2. Raise the head restraint bypulling up o

To remove the adjustable head restraint, do the following:1. Pull up the head restraint until itreaches the highest adjustmentposition.2. Simultaneous

WARNING: To minimize the risk of neck injury in the event of acrash, head restraints must be installed properly.Adjusting the front manual seat (if eq

WARNING: Reclining the seatback can cause an occupant toslide under the seat’s safety belt, resulting in severe personalinjuries in the event of a col

SPECIAL NOTICESNew Vehicle Limited WarrantyFor a detailed description of what is covered and what is not covered byyour vehicle’s New Vehicle Limited

Press the control to move the seatforward, backward, up or down.Heated seats (if equipped)WARNING: Persons who are unable to feel pain to the skinbeca

WARNING: To minimize the risk of neck injury in the event of acrash, the driver and passenger occupants should not sit inand/or operate the vehicle, u

Properly adjust the head restraint so that the top of the head restraint iseven with the top of your head and positioned as close as possible to theba

To reinstall the adjustable head restraint, do the following:1. Insert the two stems into theguide sleeve collars.2. Push the head restraint downuntil

3. Flip seat forward.Attach the safety belt web snapbutton to the quarter trim panelsnap button. This will ensure thatsafety belt does not get caught

5. Rotate seatback down into loadfloor position.Returning the second row seats to upright position1. Pull seatback up and into uprightposition making

WARNING: Make sure safety belt buckle heads are throughelastic holders on seat backs. Safety belt buckles may break ifthey are trapped underneath the

To install the second row cushion1. Push the cushion to the inboardside of the vehicle.2. Make sure that the hinges arelocked into place.SAFETY RESTRA

How does the Personal Safety System™ work?The Personal Safety System can adapt the deployment strategy of yourvehicle’s safety devices according to cr

Front passenger sensing systemFor airbags to do their job they must inflate with great force, and thisforce can pose a potentially deadly risk to occu

DATA RECORDINGService Data RecordingService data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehi

Front safety belt pretensionersThe safety belt pretensioners at the front outboard seating positions aredesigned to tighten the safety belts firmly ag

Safety restraints precautionsWARNING: Always drive and ride with your seatback uprightand the lap belt snug and low across the hips.WARNING: To reduce

WARNING: Safety belts and seats can become hot in a vehiclethat has been closed up in sunny weather; they could burn asmall child. Check seat covers a

Pregnant women should alwayswear their safety belt. The lap beltportion of a combination lap andshoulder belt should be positionedlow across the hips

When to use the automatic locking modeThis mode should be used any time a child safety seat, except abooster, is installed in passenger front or rear

WARNING: After any vehicle collision, the safety belt system atall passenger seating positions must be checked by an authorizeddealer to verify that t

WARNING: The driver and front passenger safety belt system(including retractors, buckles and height adjusters) must bereplaced if the vehicle is invol

If... Then...The driver’s safety belt isbuckled before the ignitionswitch is turned to the onposition...The safety belt warning light andindicator chi

If... Then...The driver’s and frontpassenger’s safety belts arebuckled before the ignitionswitch is turned to the onposition or less than1-2 minutes h

The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data):Reasons given... Consider...⬙Crashes are ra

limitations regarding 911 Assist and Traffic, directions andInformation privacy below). However, parties, such as lawenforcement, could combine the ED

WARNING: Do not sit on top of a buckled safety belt or insert alatchplate into the buckle to avoid the Belt-Minder威 chime. Todo so may adversely affec

1. Turn the ignition switch to the on position. DO NOT START THEENGINE.2. Wait until the safety belt warning light turns off (Approximately1 minute).•

AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)Important SRS precautionsThe SRS is designed to work withthe safety belt to help protect thedriver and right

WARNING: All occupants of the vehicle, including the driver,should always properly wear their safety belts, even when an airbag supplemental restraint

Children and airbagsChildren must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rear

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt

impact sensors, the system wiring, the airbag system readiness light, theairbag backup power and the airbag ignitors).WARNING: Several air bag system

The front passenger sensing systemuses a ⬙passenger airbag off⬙ or⬙pass airbag off⬙ indicator which willilluminate and stay lit to remind youthat the

• If the indicator lamp remains lit even after this, the person should beadvised to ride in the rear seat.OccupantPass Airbag OffIndicator LampPasseng

ObjectsPass Airbag OffIndicator LampPassenger AirbagSmall (i.e. three-ringbinder, small purse,bottled water)Unlit DisabledMedium (i.e. heavybriefcase,

CELL PHONE USEThe use of Mobile Communications Equipment has become increasinglyimportant in the conduct of business and personal affairs. However,dri

In case there is a problem with thefront passenger sensing system, theairbag readiness lamp in theinstrument cluster will stay lit.If the airbag readi

A difficulty with the system is indicated by one or more of the following:• The readiness light will eitherflash or stay lit.• The readiness light wil

How does the side airbag system work?The design and development of theside airbag system includedrecommended testing proceduresthat were developed by

WARNING: Several airbag system components get hot afterinflation. Do not touch them after inflation.WARNING: If the sideairbag has deployed, theairbag

Safety Canopy姞 SystemWARNING: Do not placeobjects or mount equipmenton or near the headliner at thesiderail that may come intocontact with a deploying

How does the Safety Canopy姞 System work?The design and development of theSafety Canopy System includedrecommended testing proceduresthat were develope

The Safety Canopy System is designed to active when the vehiclesustains lateral deceleration sufficient to cause the RCM to initiate safetycanopy infl

A difficulty with the system is indicated by one or more of the following:• The readiness light (same light as for front airbag system) will eitherfla

Important child restraint precautionsWARNING: Always make sure your child is secured properly ina device that is appropriate for their height, age and

Recommendations for Safety Restraints for ChildrenChild size, height, weight, or ageRecommendedrestraint typeInfantsor tod-dlersChildren weighing 40 l

These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag

Recommendations for attaching child safety restraints for childrenRestraintTypeChildWeightUse any attachment method as indicatedbelow by “X”LATCH(lowe

WARNING: Always carefully follow the instructions andwarnings provided by the manufacturer of any child restraint todetermine if the restraint device

training to ensure that all children ages 0 to 16 are properly restrained inthe correct restraint system. Ford recommends checking with a NHTSACertifi

Airbags can kill or injure a child in a child seat. NEVER place arear-facing child seat in front of an active airbag. If you must use aforward-facing

Perform the following steps when installing the child seat withcombination lap/shoulder belts:Note: Although the child seat illustrated is a forward f

3. While holding the shoulder andlap belt portions together, route thetongue through the child seataccording to the child seatmanufacturer’s instructi

8. Remove remaining slack from thebelt. Force the seat down with extraweight, e.g., by pressing down orkneeling on the child restraint whilepulling up

LATCH compatible child safety seats have two rigid or webbing mountedattachments that connect to the two lower anchors at the LATCHequipped seating po

WARNING: Depending on where you secure a child restraint,and depending on the child restraint design, you may blockaccess to certain safety belt buckl

Attaching child safety seats with tether strapsMany forward-facing child safety seats include a tether strap whichextends from the back of the child s

Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleasePanic Alarm Engine Oi

2. Locate the correct anchor for theselected seating position.There are three tether anchorslocated on the headliner at the rearof the vehicle.3. Clip

around four (4) years of age. Consult your child safety seat owner guidefor the weight, height, and age limits specific to your child safety seat.Keep

• Is the shoulder belt centered on the shoulder and chest?• Can the child stay seated like this for the whole trip?Types of booster seatsThere are gen

Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, a

Follow all instructions provided by the manufacturer of the booster seat.WARNING: Never place, or allow a child to place, the shoulderbelt under a chi

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERSUtility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare e

VEHICLE CHARACTERISTICS4WD system (if equipped)Your vehicle may be equipped with a four-wheel drive (4WD) system.With the 4WD option, power will be de

• Narrower — to provide greatermaneuverability in tight spaces,particularly in off-road use.As a result of the above dimensionaldifferences, SUVs and

government test course. For example, a tire graded 150 would wear oneand one-half (11⁄2) times as well on the government course as a tiregraded 100. T

• Tire Identification Number (TIN): A number on the sidewall ofeach tire providing information about the tire brand andmanufacturing plant, tire size

WARNING LIGHTS AND CHIMESShown in standard measure. Metric similar.Warning lights and gauges can alert you to a vehicle condition that maybecome serio

At least once a month and before long trips, inspect each tire and checkthe tire pressure with a tire gauge (including spare, if equipped). Inflateall

To check the pressure in your tire(s):1. Make sure the tires are cool, meaning they are not hot from drivingeven a mile.If you are checking tire press

the valve stem. Inspect the tire sidewalls for cracking, cuts, bruises andother signs of damage or excessive wear. If internal damage to the tire issu

U.S. DOT Tire Identification Number (TIN)Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the s

WARNING: When mounting replacement tires and wheels, youshould not exceed the maximum pressure indicated on thesidewall of the tire to set the beads w

Safety practicesDriving habits have a great deal to do with your tire mileage and safety.• Observe posted speed limits• Avoid fast starts, stops and t

Tire and wheel alignmentA bad jolt from hitting a curb or pothole can cause the front end of yourvehicle to become misaligned or cause damage to your

• Rear-wheel drive (RWD)vehicles/Four-wheel drive(4WD)/All-wheel drive (AWD)vehicles (front tires at top ofdiagram)Sometimes irregular tire wear can b

Information on “P” type tiresP215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (

Note: You may not find this information on all tires because it is notrequired by federal law.Letter rating Speed rating - mph (km/h)M 81 mph (130 km/

WARNING: Under engine misfire conditions, excessive exhausttemperatures could damage the catalytic converter, the fuelsystem, interior floor coverings

12. Treadwear, Traction and Temperature Grades• Treadwear: The treadwear grade is a comparative rating based on thewear rate of the tire when tested u

Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;

Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8

TIRE PRESSURE MONITORING SYSTEM (TPMS)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe inflation pre

The tire pressure monitoring system complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing tw

When your temporary spare tire is installedWhen one of your road tires needs to be replaced with the temporaryspare, the TPMS system will continue to

Low tire pressurewarning lightPossiblecauseCustomer action requiredFlashing warninglightSpare tirein useYour temporary spare tire is in use.Repair the

SNOW TIRES AND CABLESWARNING: Snow tires must be the same size, load index, speedrating as those originally provided by Ford. Use of any tire orwheel

VEHICLE LOADING – WITH AND WITHOUT A TRAILERThis section will guide you in the proper loading of your vehicle and/ortrailer, to keep your loaded vehic

Payload – is the combined weight of cargo and passengers that thevehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Lab

Seating and Safety Restraints 115Seating 115Safety restraints 127Airbags 142Child restraints 157Tires, Wheels and Loading 175Tire information 177Tire

Safety belt: Reminds you to fastenyour safety belt. A Belt-Minder威chime will also sound to remind youto fasten your safety belt. Refer tothe Seating a

Example only:Tires, Wheels and Loading2002011 Escape Hybrid (ehv)Owners Guide, 2nd PrintingUSA (fus)

Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue loador king pin w

• Example only:WARNING: Exceeding the Safety Compliance Certification Labelvehicle weight rating limits could result in substandard vehiclehandling or

GCW (Gross Combined Weight) – is the weight of the loaded vehicle(GVW) plus the weight of the fully loaded trailer.GCWR (Gross Combined Weight Rating)

WARNING: Exceeding any vehicle weight rating limitation couldresult in serious damage to the vehicle and/or personal injury.Steps for determining the

to transport the cement to your home? If you and your friend eachweigh 220 lb. (99 kg), the calculation would be: 1400 - (2 x 220) - (12x 100) = 1400

Follow these guidelines to ensure safe towing:• Do not tow a trailer until your vehicle has been driven at least1,000 miles (1,600 km).• Consult your

WARNING: Towing trailers beyond the maximum recommendedgross trailer weight exceeds the limit of the vehicle and couldresult in engine damage, transmi

Trailer lampsTrailer lamps are required on most towed vehicles. Make sure all runninglights, brake lights, turn signals and hazard lights are working.

Trailer towing tips• Practice turning, stopping and backing-up before starting on a trip toget the feel of the vehicle-trailer combination. When turni

High engine or high motorelectronic coolant temperature:Illuminates when the engine coolantor motor electronics coolant temperature is high. The messa

RECREATIONAL TOWINGAn example of “recreational towing” is towing your vehicle behind amotorhome.Note: Put your climate control system in recirculated

STARTINGPositions of the ignition1. Off— locks the gearshift leverand allows key removal.2. Accessory— allows the electricalaccessories such as the ra

Important safety precautionsA computer system controls the engine’s idle revolutions per minute(RPM). When the engine starts, the idle RPM runs higher

3. Turn the key to 3 (on) withoutturning the key to 4 (start).Some warning lights will briefly illuminate. See Warning lights andchimes in the Instrum

Note: If the engine fails to start when it should, which is indicated bythe service engine soonlight , put the gearshift lever into P (Park),turn the

Prior to using the engine block heater, follow these recommendations forproper and safe operation:• For your safety, use an outdoor extension cord tha

factory installed block heater system does not have a thermostat;however, maximum temperature is attained after approximately threehours of operation.

distance. The ABS will be activated immediately, allowing you to retainsteering control during hard braking and on slippery surfaces. However,the ABS

Parking brakeApply the parking brake wheneverthe vehicle is parked. To set theparking brake, press the parkingbrake pedal down until the pedalstops.Th

Pull the release lever to release thebrake. Driving with the parkingbrake on will cause the brakes towear out quickly and reduce fueleconomy.ADVANCETR

Low fuel: Illuminates when the fuellevel in the fuel tank is at or nearempty (refer to Fuel gauge in thischapter).Speed control: Illuminates whenthe s

WARNING: Remember that even advanced technology cannotdefy the laws of physics. It’s always possible to lose control of avehicle due to inappropriate

When AdvanceTrac威 with RSC威 performs a normal system self-check,some drivers may notice a slight movement of the brake, and/or arumble, grunting, or g

or avoiding objects in the roadway. ESC operates by applying brakes toone or more of the wheels individually and, if necessary, reducing enginepower i

can be restored by pressing the traction control off button again, or byturning off and restarting the engine.If you switch off the traction control,

WARNING: Trailer sway control does not prevent a trailer fromswaying, it mitigates the sway from increasing once it hasoccurred. TSC cannot stop all t

more effort. Under extreme usage conditions, the steering effort mayincrease. This occurs to prevent overheating and permanent damage toyour steering

WARNING: Loaded vehicles, with a higher center of gravity,may handle differently than unloaded vehicles. Do not overloadyour vehicle and use extra pre

WARNING: Do not drive your vehicle until you verify that thebrake lamps are working.WARNING: Always set the parking brake fully and make surethe gears

R (Reverse)With the gearshift lever in R (Reverse), the vehicle will move backward.Always come to a complete stop before shifting into and out of R(Re

REVERSE SENSING SYSTEM (IF EQUIPPED)The reverse sensing system (RSS) sounds a tone to warn the driver ofobstacles near the rear bumper when R (Reverse

HEV engine off reminder chime: Sounds for 10 seconds when thePRNDL is in the P (Park) position and the Driver’s door is ajar (open)while ignition is o

The RSS detects obstacles up to6 feet (1.8 meters) from the rearbumper with a decreased coveragearea at the outer corners of thebumper, (refer to the

REARVIEW CAMERA SYSTEM (IF EQUIPPED)The rearview camera system locatedon the liftgate provides a videoimage, which appears in therearview mirror or on

Note: The default setting for the camera delay is off. Press the“Settings” button found on the navigation screen (if equipped) to set thecamera delay

• If the image is not clear, then check if there is anything covering thelens such as dirt, mud, ice, snow, etc. If the image is still not clearafter

For best performance, the driver should drive the vehicle as parallel aspossible while passing a parking space. If driven too fast (above 18 mph[30 km

When you determine the vehicle is back far enough or you hear a solidtone from reverse sensing system, bring the vehicle to a complete stopand move th

• Exceeding a vehicle speed of 6 mph (10 km/h) during automaticsteering• Deactivating the AdvanceTrac威 system or the system has activated ona slippery

Why doesn’t APA position the vehicle where I want in the space?• The driver allows the vehicle to roll in the opposite direction of thetransmission, s

Driving with blind spot mirrorsBefore a lane change, check themain mirror first, then check theblind spot mirror. If no vehicles arepresent in the bli

Driving off-road with truck and utility vehicles4WD vehicles are specially equipped for driving on sand, snow, mud andrough terrain and have operating

Battery gauge: Providesinformation about the vehicle’senergy usage.• ASSIST — Battery provides extrapower to boost the vehicle’sacceleration.• CHARGE

sideways out of control or roll over. Remember, your safety and thesafety of others should be your primary concern.WARNING: Vehicles with a higher cen

Emergency maneuvers• In an unavoidable emergency situation where a sudden sharp turnmust be made, remember to avoid “over-driving” your vehicle, i.e.,

Mud and waterIf you must drive through highwater, drive slowly. Traction orbrake capability may be limited.When driving through water,determine the de

slopes or hills. A danger lies in losing traction, slipping sideways andpossibly rolling over. Whenever driving on a hill, determine beforehandthe rou

Avoid sudden braking as well. Although a 4WD vehicle may acceleratebetter than a two-wheel drive vehicle in snow and ice, it won’t stop anyfaster, bec

DRIVING THROUGH WATERIf driving through deep or standingwater is unavoidable, proceed veryslowly especially when the depth isnot known. Never drive th

ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside

Canadian customers refer to your Customer Information Guidefor information on:• coverage period• exact fuel amounts• towing of your disabled vehicle•

HAZARD FLASHER CONTROLThe hazard flasher is located on thesteering column, just behind thesteering wheel. The hazard flasherswill operate when the ign

The fuel pump shut-off switch islocated in the front passenger’sfootwell, behind a flip-up cover.The high voltage shut-off switch islocated in the car

MESSAGE CENTERYour vehicle’s message center is capable of monitoring many vehiclesystems and will alert you to potential vehicle problems and variousc

If you see or smell fuel, do not reset the fuel pump shut-off or try tostart your vehicle; you could injure yourself or others. Have all thepassengers

Passenger compartment fuse panelThe fuse panel is located on theright-hand side of the centerconsole, by the instrument panel.Remove the panel cover t

Fuse/RelayLocationFuse AmpRatingProtected Circuits4 30A Moon roof5 10A Brake-shift i nterlock (BSI), Passengercompartment fuse panel, Keypadilluminati

Fuse/RelayLocationFuse AmpRatingProtected Circuits32 10A Rear video camera module33 10A Not used (spare)34 5A Not used (spare)35 10A Four wheel drive,

WARNING: Always disconnect the low voltage (underhood)battery before servicing high current fuses.WARNING: To reduce risk of electrical shock, always

Fuse/RelayLocationFuse AmpRatingProtected Circuits7 15A* Liftgate latch8 5A* Traction battery control module9 50A** Brake control module10 30A** Front

Fuse/RelayLocationFuse AmpRatingProtected Circuits30A — Cooling fan 1 relay30B — Electric vacuum pump mechanical relay30C — Cooling fan main relay30D

Auxiliary relay boxThe relay box is located in the engine compartment on the radiatorsupport bracket.Fuse/RelaylocationFuse ampratingDescriptionRelay

Note: The tire pressure monitoring system (TPMS) indicator light willilluminate when the spare tire is in use. To restore the full functionalityof the

When driving with one of the dissimilar spare tires listed above, do not:• Exceed 50 mph (80 km/h)• Load the vehicle beyond maximum vehicle load ratin

AVG MPG (L/100km)Average fuel economy displays your average fuel economy in miles/gallonor liters/100 km.If you calculate your average fuel economy by

When driving with the full-size dissimilar spare tire/wheel additionalcaution should be given to:• Towing a trailer• Driving vehicles equipped with a

To remove jack from vehicle:1. Release the thumbscrew on thebracket.2. Release the retention clip on theupper part of the jack bracket.3. Dislodge the

If equipped with a tether, perform the following additional steps:4. Lift the spare tire on end toaccess tether attachment (1).5. Use the lug wrench t

WARNING: To help prevent the vehicle from moving when youchange a tire, be sure the parking brake is set, then block (inboth directions) the wheel tha

Before placing the jack under the vehicle, NOTE the jack locations:• FrontView shown from rear of front tire.Position the jack directly below theprotr

• RearView shown from forward of reartire. Position the jack directly belowthe stud on the rear trailing arm.3. Position the jack according to theguid

Never use the differentials as ajacking point.WARNING: To lessen therisk of personal injury, donot put any part of your bodyunder the vehicle while ch

• guide the jack bottom first in thetrim opening and position in thebracket (3),• secure the retention clip on theupper part of the jack (2), and• clo

4. Slide the wheel partially under the vehicle and install the retainerthrough the center of the wheel.5. Turn the jack handle clockwise until the tir

Note: Inspect the wheel pilot holeprior to installation. If there isvisible corrosion in wheel pilot hole,remove loose particles by wipingwith clean r

System check and vehicle feature customizationPress the SETUP button repeatedlyto cycle the message center throughthe following features:PRESS RESET F

Preparing your vehicleIf your low voltage (underhood) battery becomes disconnected ordisabled for any reason, the vehicle controller must relearn the

1. Connect the positive (+) jumpercable to the positive (+) terminal ofthe discharged battery.2. Connect the other end of thepositive (+) cable to the

Removing the jumper cablesRemove the jumper cables in the reverse order that they wereconnected.Note: In the illustration, the vehicle on the bottom i

WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y

Ford Motor Company produces a towing manual for all authorized towtruck operators. Have your tow truck operator refer to this manual forproper hook-up

GETTING THE SERVICES YOU NEEDWarranty repairs to your vehicle must be performed by an authorizedFord, Lincoln, or Mercury dealer. While any authorized

In Canada:Mailing address (Ford vehicles)Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4Teleph

In some states, you must directly notify Ford in writing before pursuingremedies under your state’s warranty laws. Ford is also allowed a finalrepair

In the case of 1 or 2 above, the consumer must also notify themanufacturer of the need for the repair of the nonconformity at thefollowing address:For

for your name and address, general information about your new vehicle,information about your warranty concerns, and any steps you havealready taken to

Note: To change oil life 100% value to another value, proceed to Step 3.3. Once “OIL LIFE SET TO XXX%” is displayed, release and press theRESET button

GETTING ASSISTANCE OUTSIDE THE U.S. AND CANADABefore exporting your vehicle to a foreign country, contact theappropriate foreign embassy or consulate.

If your vehicle must be serviced while you are traveling or living in theMiddle East, contact the nearest authorized dealer. If the authorizeddealer c

REPORTING SAFETY DEFECTS (U.S. ONLY)If you believe that your vehicle hasa defect which could cause a crashor could cause injury or death, youshould im

WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft威 Detail Wash (ZC-3-A), which i

• Do not allow paint sealant to come in contact with any non-body(low-gloss black) colored trim, such as grained door handles, roofracks, bumpers, sid

• Spray Motorcraft威 Engine Shampoo and Degreaser (ZC-20) on allparts that require cleaning and pressure rinse clean. In Canada, useMotorcraft威 Engine

vehicle’s glass or the wiper blades may be the cause. These may includehot wax treatments used by commercial car washes, water repellentcoatings, tree

• Do not use household or glass cleaners as these may damage thefinish of the instrument panel, interior trim and cluster lens.• Do not allow air fres

WARNING: Do not use cleaning solvents, bleach or dye on thevehicle’s safety belts, as these actions may weaken the beltwebbing.WARNING: On vehicles eq

For routine cleaning, wipe the surface with a soft, damp cloth. For morethorough cleaning, wipe the surface with a mild soap and water solution.• Clea

LANGUAGE = ENGLISH / SPANISH / FRENCHAllows you to choose which language the message center will display in.Selectable languages are English, Spanish,

FORD AND LINCOLN CAR CARE PRODUCTSYour Ford or Lincoln authorized dealer has many quality productsavailable to clean your vehicle and protect its fini

SERVICE RECOMMENDATIONSTo help you service your vehicle, we provide scheduled maintenanceinformation which makes tracking routine service easy.If your

The following are specific locations in the rear cargo area that consist ofhigh voltage components and/or wiring.1. High voltage connector shield2. Se

Working with the engine off1. Set the parking brake and ensure the gearshift is securely latched in P(Park).2. Turn off the engine and remove the key.

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT1. Engine coolant reservoir2. Motor/Electronics (M/E) coolant reservoir3. Engine oil filler cap4. Brak

WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer

CHANGING THE WIPER BLADES1. Pull the wiper blade and armaway from the glass.2. Squeeze the locking tabs torelease the blade from the arm andpull the b

Changing rear window wiper bladeThe rear wiper arm is designed without a service position. This reducesthe risk of damage to the blade in an automatic

5. Locate and carefully remove the engine oil level dipstick.6. Wipe the dipstick clean. Insert the dipstick fully, then remove it again.• If the oil

To avoid possible oil loss, DO NOT operate the vehicle with theengine oil level dipstick and/or the engine oil filler cap removed.Engine oil and filte

Maintenance and Specifications 291Engine compartment 294Engine oil 297Battery 300Engine Coolant and Motor/Electronics Coolant 302Fuel information 308A

Note: If the vehicle is still running, it may soon shut down withoutfurther warning and should be stopped safely. Contact your authorizeddealer as soo

It is recommended you use the appropriate Motorcraft威 oil filter oranother with equivalent performance for your engine application.LOW VOLTAGE (UNDERH

WARNING: Keep batteries out of reach of children. Batteriescontain sulfuric acid. Avoid contact with skin, eyes or clothing.Shield your eyes when work

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recyclin

Checking engine coolantThe concentration and level ofengine coolant should be checked atthe intervals listed in scheduledmaintenance information. Thec

Checking motor/electronics (M/E) coolantThe M/E coolant reservoir is locatedbehind the engine coolant reservoir.Refer to the following enginecoolant s

If the engine coolant has not been checked at the recommended interval,the engine coolant reservoir may become low or empty. If the reservoir islow or

• Do not add extra inhibitors or additives to the coolant. Thesecan be harmful and compromise the corrosion protection of the enginecoolant.For vehicl

If you have to add more than 1.0 quart (1.0 liter) of engine coolant permonth, have your authorized dealer check the engine cooling system.Your coolin

• A coolant concentration of 40% will provide freeze pointprotection down to -12°F [-24°C]. Decreased engine coolantconcentrations below 40% will decr

Observe the following guidelines when handling automotive fuel:• Extinguish all smoking materialsand any open flames beforerefueling your vehicle.• Al

BRAKE FLUID LEVEL LOW — Indicates the brake fluid level is lowand the brake system should be inspected immediately. Refer to Brakefluid in the Mainten

RefuelingWARNING: Fuel vapor burns violently and a fuel fire can causesevere injuries. To help avoid injuries to you and others:• Read and follow all

4. After you are done pumping fuel, slowly remove the fuel fillernozzle—allow about five seconds after pumping fuel before removing thefuel filler noz

Choosing the right fuelUse only UNLEADED fuel or UNLEADED fuel blended with a maximumof 10% ethanol. Do not use fuel ethanol (E85), diesel, methanol,

performance and emission control system protection for your vehicle.Gasolines that meet the World-Wide Fuel Charter should be used whenavailable. Ask

1. Locate the white plastic funnel. Itis attached to the inside of the rearpassenger side cargo compartmentaccess door.2. Slowly insert the funnel int

Filling the tankWhen the fuel gauge indicates empty, there is still a small reserve of fuelin the fuel system. When refueling your vehicle after the f

Driving style — good driving and fuel economy habitsSince it is able to operate in electric mode and to collect braking energy,your hybrid vehicle may

Conditions• Heavily loading a vehicle or towing a trailer may reduce fuel economyat any speed.• Carrying unnecessary weight may reduce fuel economy (a

smoke or loss of engine power could indicate that the emission controlsystem is not working properly.An improperly operating or damaged exhaust system

indicator should stay off the next time the engine is started. A drivingcycle consists of a cold engine startup followed by mixed city/highwaydriving.

VEHICLE NEAR TOP SPEED — Displayed when a MyKey™ is in useand the MyKey speed limit is on and the vehicle speed is approaching80 mph (130 km/h). Refer

engine must warm up to its normal operating temperature. Once started,do not turn off the engine until the above driving cycle is complete. Ifthe vehi

WARNING: To reduce the risk of vehicle damage and/orpersonal burn injuries do not start your engine with the aircleaner removed and do not remove it w

General• Store all vehicles in a dry, ventilated place.• Protect from sunlight, if possible.• If vehicles are stored outside, they require regular mai

Cooling system• Protect against freezing temperatures.• When removing vehicle from storage, check coolant fluid level.Confirm there are no cooling sys

• If the battery was removed, clean the battery cable ends and inspect.If you have any concerns or issues, contact your authorized dealer.MOTORCRAFT P

MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItem CapacityFord Part Name orequivalentFord Part Number / FordSpecificationBrake fluidBetween MINand

Item CapacityFord Part Name orequivalentFord Part Number / FordSpecificationEngine oil 5.3 quarts (5.0L)•Motorcraft威 SAE5W-20 PremiumSynthetic Blend M

Item CapacityFord Part Name orequivalentFord Part Number / FordSpecificationWindshield washerfluidFill as requiredMotorcraft威 PremiumWindshield Washer

ENGINE DATAEngine 2.5L I4 engineCubic inches 152Required fuel 87 octaneFiring order 1-3-4-2Ignition system Coil on plugSpark plug gap 0.049–0.053 inch

IDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations requirethat a Safety Compli

SPACE FOUND PULL FORWARD (if equipped) — May display whenusing the active park assist system. See Active park assist in theDriving chapter for more in

The Vehicle Identification Number (VIN) contains the followinginformation:1. World manufacturer identifier2. Brake system / Gross VehicleWeight Rating

FORD CUSTOM ACCESSORIES FOR YOUR VEHICLEA wide selection of Ford Custom Accessories are available for yourvehicle through your local Ford or Ford of C

Lifestyle•Ash cup / smoker’s package •Roof racks and carriers*•Cross bars •Rear bumper protector*•Navigation* •Cargo net*•SUV camping net* •Cargo orga

• Mobile communications systems may harm the operation of yourvehicle, particularly if they are not properly designed for automotiveuse.• To avoid int

FORD ESP EXTENDED SERVICE PLANS (U.S. ONLY)More than 30 million Ford, Lincoln, and Mercury owners have discoveredthe powerful protection of Ford ESP.

Ford ESP Can Quickly Pay for ItselfOne service bill – the cost of parts and labor – can easily exceed theprice of your Ford ESP Service Contract. With

Ford Extended Service Plan3362011 Escape Hybrid (ehv)Owners Guide, 2nd PrintingUSA (fus)

FORD ESP EXTENDED SERVICE PLANS (CANADA ONLY)You can get more protection for your vehicle by purchasing a FordExtended Service Plan (ESP). Ford ESP is

GENERAL MAINTENANCE INFORMATIONWhy maintain your vehicle?This guide describes the scheduled maintenance required for yourvehicle. Carefully following

Ford strongly recommends the use of genuine Ford replacement parts.Parts other than Ford, Motorcraft威 or Ford-authorized remanufacturedparts that are

AUDIO SYSTEMSAM/FM/single CD/MP3 satellite compatible sound systemWARNING: Driving while distracted can result in loss of vehiclecontrol, accident and

Factory-trained techniciansFord and Lincoln Mercury service technicians participate in extensivefactory-sponsored certification training to help them

Multi-point inspectionIn order to keep your vehicle running right, it is important to have thesystems on your vehicle checked regularly. This can help

Be sure to ask your Ford or Lincoln Mercury dealership service advisoror technician about the multi-point vehicle inspection. It’s acomprehensive way

Scheduled Maintenance Guide3432011 Escape Hybrid (ehv)Owners Guide, 2nd PrintingUSA (fus)

NORMAL SCHEDULED MAINTENANCE AND LOGThe following section contains the “Normal Schedule”. This schedule ispresented at specific mileage (kilometer) in

Miles (x 1,000) 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150Kilometers (x 1,000) 16 32 48 64 80 96 112 128 144 160 176 192 208 224 240Months 12

Every 20,000 miles(32,000 km)Replace cabin air filter (if equipped)Every 30,000 miles(48,000 km)Replace climate-controlled seat filter(if equipped)Rep

Maintenance schedule logDEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDAT

DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HO

DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HO

AM/FM Radio/ VOL (Power/Volume): Pressto turn the radio on/off. Turn theknob to increase/decrease volume.If the volume is set above a certainlevel and

SPECIAL OPERATING CONDITIONSIf you operate your Ford/Lincoln/Mercury vehicle primarily in one of themore demanding Special Operating Conditions listed

Operating in dusty conditions such as unpaved or dusty roadsInspect frequently, service asrequired– Replace cabin air filter (if equipped).– Replace e

Special operating condition logDEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER

DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HO

EXCEPTIONSIn addition, there are several exceptions to the Normal Schedule. Theyare listed below:Normal vehicle axle maintenance❑Rear axles and power

COOLANT CHANGE RECORDEngine coolant❑6 years or 100,000 miles (160,000 km) - change engine and motor/electronics coolant (whichever comes first).❑After

Engine coolant change logDEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDA

AAccessory delay ...77Active Park Assist ...233AdvanceTrac ...219Air cleaner filte

Child safety seats ...162attaching with tetherstraps ...169in front seat ...

filter, specifications ...299, 324recommendations ...299refill capacities ...325specifications ...

To activate the autoset feature: Press MENU repeatedly until AUTOPRESET ON/OFF appears in the display. UseSEEK/TRACK toturn AUTO PRESET to ON, and eit

JJack ...257positioning ...257storage ...257Jum

Parts(see Motorcraft威 parts) ...324Passenger OccupantClassification Sensor ...129Power distribution box(see Fuses) ...

Snowplowing ...12SOS Post Crash Alert ...157Spark plugs,specifications ...324, 328Special no

WWarning lights (see Lights) ...18Washer fluid ...295Water, Driving through ...245Windowspower ...

/ Play/Pause: Press toplay/pause a track when playing aCD.SEEK/TRACK: PressSEEK/TRACK to access theprevious/next track.CAT (Category) / FOLD (Folder):

SHUFFLE: Press SHUFFLE to turn on and off and begin/stop randomplay. The system will only shuffle the disc currently playing.Satellite RadioSatellite

MEMORY PRESETS (0–9): Thereare 30 available presets, 10 each forSAT1, SAT2 and SAT3. To savesatellite channels in your memorypresets, tune to the desi

CONGRATULATIONSCongratulations on acquiring your new Ford Hybrid. Please take the timeto get well acquainted with your vehicle by reading this handboo

an audible prompt. Press OK while SONG ALERT is in the display andthe system will take you to the channel playing the desired song. Youcan save up to

b. CHANGE PIN: Press OK when CHANGE PIN is displayed. Thedisplay will read ENTER OLD PIN. Enter your current (old) PINnumber and when the system accep

Extra FeaturesAUX: Press repeatedly to cycle through LINE IN (auxiliary audio mode),and SYNC威 (if equipped).For location and further information on au

Your vehicle is equipped with anAuxiliary Input Jack (AIJ). TheAuxiliary Input Jack provides a wayto connect your portable musicplayer to the in-vehic

7. Adjust the sound on your portable music player until it reaches thelevel of the FM station or CD by switching back and forth between theAUX and FM

Your vehicle may be equipped with aUSB port located on the instrumentpanel. This feature allows you toplug in media playing devices,memory sticks, and

CD/CD player careDo:• Handle discs by their edges only.(Never touch the playingsurface).• Inspect discs before playing.• Clean only with an approved C

CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommen

Sample MP3 structureIf you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variou

• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere w

SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury to yourself or others? Inthis guide, answ

Radio Display Condition Action RequiredINVALID CHNL Channel no longeravailable.This previously availablechannel is no longeravailable. Tune to another

Radio Display Condition Action RequiredCALL SIRIUS威1–888–539–7474Satellite service hasbeen deactivated bySIRIUS威 SatelliteRadio.Call SIRIUS威 at1–888–5

DUAL AUTOMATIC TEMPERATURE CONTROL1. AUTO/Driver temperature: Press to engage full automaticoperation. The system will automatically determine fan spe

5. Power/ : Press to activate/deactivate the climate controlsystem. When the system is off, outside air is shut out. Press +or– to manually increase/d

11. Recirculated air: Press to activate/deactivate air recirculationin the vehicle. Recirculated air may reduce the amount of time needed tocool down

• A small amount of air may be felt from the floor vent regardless of theair distribution setting that is selected.During extreme high ambient tempera

REAR WINDOW DEFROSTERRThe rear defroster control is located on the climate control panel andworks to clear the rear window of fog and thin ice.The veh

HEADLAMP CONTROLRotate the headlamp control to thefirst positionto turn on theparking lamps.Rotate to the second positiontoturn on the headlamps.Rotat

2. Rotate the headlamp control to the autolamp position.3. Rotate the headlamp control to the off position.4. Turn the vehicle on.5. Turn the vehicle

Flash-to-passPull toward you slightly to activateand release to deactivate.Daytime running lamps (DRL) (if equipped)Turns the low beam headlamps on wi

new vehicle operation. Vary your speed frequently in order to give themoving parts a chance to break in.Drive your new vehicle at least 1,000 miles (1

Note: If the battery is disconnected, discharged, or a new battery isinstalled, the dimmer switch requires re-calibration. Rotate the dimmerswitch fro

5. Locate the vertical adjuster onthe headlamp, then use a 4 mmsocket to turn the adjuster eithercounterclockwise (to adjust up) orclockwise (to adjus

The map lamp controls (withoutmoon roof) are located on the domelamp. Press the button on eitherside of each map lamp to illuminatethe lamps. Press th

Ambient lighting (if equipped)Illuminates footwells, cupholders,the console bin and the console traywith a choice of several colors. Theambient lighti

Take your vehicle to a dealer for service if any of the above conditions ofunacceptable moisture are present.Using the right bulbsReplacement bulbs ar

Replacing headlamp bulbs1. Make sure that the headlamp control is in the off position.2. Open the hood.3. Reach over the front bolster.4. Remove the b

5. Carefully pull the bulb out of thesocket and push in the new bulb.6. Install the bulb socket into thelamp assembly and rotate clockwise.Replacing f

Replacing license plate lamp bulbs1. Make sure the headlamp switch isin the off position.2. Depress the lever and carefullypry the license plate lamp

3. Pull the bulb straight out of thesocket and push in the new bulb.To complete installation, follow theremoval procedure in reverse order.Replacing f

MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the

• Charge level of high voltage battery is low• Very high or low outside temperature (to provide systemcooling/heating)• Engine not warm enough to prov

Rear window wiper/washer controlsFor rear wiper operation, rotate therear window wiper and washercontrol to the desired position.Select:2 — Normal spe

ILLUMINATED VISOR MIRRORLift the mirror cover to turn on thevisor mirror lamps.Slide-on-rod featureThe visor will slide back and forthon the rod for i

Compass zone adjustment1. Determine which magnetic zoneyou are in for your geographiclocation by referring to the zonemap.2. Turn ignition to the on p

2. To calibrate, press and hold theRESET control for approximatelyten seconds until CAL appears.Release the control.3. Slowly drive the vehicle in aci

The tray and inside bin can beremoved to open up space to fit alaptop computer, MP3 players, CDsor handbags. To remove, open theconsole lid and pull t

To have full capacity usage of your power point, the engine is required tobe running to avoid unintentional discharge of the battery. To preventthe ba

defeat the safety protection design provided by the cap and twisttab. It will also cause the power point to overload due topowering multiple devices t

One-touch downAllows the driver’s window to open fully without holding the controldown. Press the switch completely down to the second detent andrelea

Note: A rear center passenger and/or raised rear center headrest (ifequipped) may also block the light from reaching the sensor.Do not clean the housi

Heated outside mirrors (if equipped)Both mirrors are heatedautomatically to remove ice, mistand fog when the rear windowdefrost is activated.Do not re

If the vehicle is left inoperative for over 31 days, it may be necessary tojumpstart the vehicle. For more information, refer to Jump starting(Low vol

3. Press and release SET +.4. Take your foot off the accelerator pedal.5. The indicatorlight on the instrument cluster will turn on.Note:• Vehicle spe

Turning off speed controlTo turn off the speed control, press OFF or turn off the ignition.Note: When you turn off the speed control or the ignition,

SYNC威 system hands-freecontrol feature (if equipped)Press briefly to use the voicecommand feature. You will hear atone and LISTENING will appear inthe

To open the moon roof: The moonroof is equipped with an automatic,one-touch, opening, closing andventing feature. Press and releasethe rear portion of

The moon roof has a sliding shade that can be opened or closed whenthe glass panel is shut. To close the shade, pull it toward the front of thevehicle

Read the instructions completely before attempting to program theCar2U威 system. Because of the steps involved, it may be helpful to haveanother person

1. Firmly press the two outerCar2U威 system buttons for1–2 seconds, then release.2. Go to the garage to locate thegarage door opener motor and its“lear

After successful programming, you will be able to operate your Car2U威system by pressing the button you programmed to activate the opener.The indicator

Switchposition 12345678 9101112Up, onor +LLLLLLLL L L L LMiddle,neutralor 0MMMMMMMMMMMMDown,off or –RRRRRRRR R R R RL=left; M=middle; R=right3. To inp

5. Press and hold the Car2U威system button you would like to useto control the garage door.Immediately (within 1 second)release the button once the gar

achieved with mild to moderate acceleration and deceleration. Moderatebraking is particularly important since it allows you to maximize theenergy capt

FCC and RSS-210 Industry Canada ComplianceThe Car2U威 system complies with Part 15 of the FCC rules and withRSS-210 of Industry Canada. Operation is su

Do not open the liftgate or liftgate window in a garage or other enclosedarea with a low ceiling. If the liftgate window is raised and the liftgate is

WARNING: Do not place any objects on the cargo area shade.They may obstruct your vision or strike occupants of vehicle inthe case of a sudden stop or

To remove the cross-bar assembly (if equipped) from the roof rackside rails:1. Loosen the thumbwheel at bothends of the cross-bar (bothcross-bars are

To reinstall the cross-bar assembly (if equipped) to the roof rackside rails:1. Ensure that both cross-barassemblies are installed with the F(front) a

KEYSYour vehicle is equipped with twoIntegrated Keyhead Transmitters(IKTs). The key blade functions as aprogrammed key which starts thevehicle and unl

MYKEY™The MyKey™ feature allows you to program a restricted driving mode topromote good driving habits. All but one of the keys programmed to thevehic

Create a MyKey™To program MyKey™ on one of the keys programmed to the vehicle,insert the key that you want to make a MyKey™ into the ignition. Turnthe

Clear MyKey™To reset all MyKeys™ as admin keys do the following:1. Turn the vehicle on using the admin key.2. Press SETUP until PRESS RESET TO CLEAR M

3. Follow Steps 1-4 in the Create a MyKey™ section.Note: For all vehicles, the number of MYKEY(S) PROGRAMMED orADMIN KEYS PROGRAMMED that is displayed